Popp 009402 Manual

Popp Røgdetektor 009402

Læs gratis den danske manual til Popp 009402 (4 sider) i kategorien Røgdetektor. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Popp 009402, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Quick Start

This device is a combination of a Z-Wave sensor (smoke sensor) and a Z-Wave actuator. Please insert the Z-Wave module

including battery into the device housing first. Pressing the 'Z-Wave button' includes and excludes the device. It supports secure

communication.

Please refer to the chapters below for detailed information about all aspects of the products usage.

10-Year Smoke Detector

Manual

009402

Product Description

This product combines a certified '10 year' stand-alone smoke detector with a plug-in Z-Wave module to form a wirelessly

reporting automatically meshing smoke sensor plus wirelessly controllable indoor siren. The smoke detector’s sensor head is

certified with the Q quality label, conforms DIN EN 14604 and satisfies all contemporary legal requirements.

The High-End 10-years smoke detector offers a large test button conveniently accessible even with a broomstick when mounted

on the sealing. The smoke chamber is monitored electronically to avoid any malfunction and wrong alerts. The device will also

report its end of life to make sure it is getting replaced on time.

Furthermore, the device can be used as an independent indoor siren within the Z-Wave network, which can alarm in case of

detected flood or burglary. Please consider that the additional siren function will influence battery lifetime!

The smoke sensor and the Z-Wave controller communicate via a secure protocol to prevent manipulation.

Installation Guidelines

Please refer to the installation guide of the smoke sensor for information about how and where the smoke sensor should be

installed. The installation guide complies with the norm DIN EN 14676.

• The first step is to mount the mounting base on the desired place in the home using screws.

• Remove the battery isolation strip from the wireless module. The red LED will start blinking.

• Include the Smoke Sensor into your existing Z-Wave based Smart Home Network using the Z-Wave button.

• Place the Smoke Detector on the mounting base and turn clockwise. Now the Smoke Detector is armed.

• Battery Change: The battery of the wireless module will be empty much earlier than the 10 years soldered in battery of the

smoke sensor. To replace the battery, remove the Smoke Detector, pull off the wireless module from the smoke sensor.

Then you can replace the 1/2 AA battery and replug the wireless module.

Behavior within the Z-Wave Network

On factory default the device does not belong to any Z-Wave network. The device needs to join an existing wireless network to

communicate with the devices of this network. This process is called Inclusion. Devices can also leave a network. This process

is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller will be turned

into exclusion respective inclusion mode. Please refer to your primary controller’s manual on how to turn your controller into

inclusion or exclusion mode. Only if the primary controller is in inclusion or exclusion mode, this device can join or leave the

network. Leaving the network – i.e. being excluded – sets the device back to factory default.

If the device already belongs to a network, follow the exclusion process before including it in your network. Otherwise inclusion

of this device will fail. If the controller being included was a primary controller, it has to be reset first.

Pressing the Z-Wave button includes the device. If the button is pressed for at least 3 seconds, the inclusion will be done

without the Security Command Class. A single click on the button will exclude the device.

Operating the Device

In case smoke is detected by the smoke detector the device will sound and the wireless module will issue a Z-Wave alarm

command to the main controller and other associated devices. A low battery of the wireless module will be reported by the

wireless module. Please note that the battery level of the main detector is not reported since this battery can’t be replaced

anyway. The end-of-life indicator serves the same purpose.

Outside

Inside

Produkt Specifikationer

Mærke:	Popp
Kategori:	Røgdetektor
Model:	009402
Bredde:	115 mm
Dybde:	47 mm
Højde:	115 mm
Vægt:	202 g
Brugervejledning:	Ja
Produktfarve:	Hvid
Batteriteknologi:	Lithium
Forbindelsesteknologi:	Trådløs
Strømkilde:	Batteri
Detektor type:	Fotoelektrisk refleksion detektor
Test-knap:	Ja
Alarm decibel:	85 dB
Batterilevetid:	11 År
Alarmmute:	Ja