Pyle PLUTV42CH.5 Manual
Læs gratis den danske manual til Pyle PLUTV42CH.5 (10 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 67 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 34 anmeldelser. Har du et spørgsmål om Pyle PLUTV42CH.5, eller vil du spørge andre brugere om produktet?
Side 1/10
PLUTV42CH
800W Waterproof Marine Speakers
+ 2 Ch. Rated Amplifier
ATV, UTV, 4x4, Jeep, Wired RCA, AUX, and MP3 Audio Input Cable,
for Boat Stereo Speaker & Other Watercraft
www.PyleUSA.com
2
PRECAUTIONS
• This unit is designed for negative ground 12-14.50 Volts (DC) operation only.
• Use speakers with an impedance of 4 Ohms
• Avoid installing the unit where:
• It would be subject to high temperatures, such as from direct sunlight or hot air
from the heater.
• It would be exposed to rain or moisture.
• It would be subject to dust or dirt.
• If your vehicle or boat is parked in direct sunlight and there is a considerable
rise in temperature inside the car, allow the unit to cool off before operation.
• When installing the unit horizontally, be sure not to cover the heatsink ns with
the oor carpet.
• If this unit is placed too close to the resources radio, an interference may occur.
In this case, separate the amplier from the car radio.
• This power amplier employs a protection circuit to protect the transistors and
speakers if the amplier malfunctions.Do not attempt to test the protection
circuits by covering the heatsink or connecting improper loads.
• Do not use the unit with a weak auto battery as its optimum performance
depends on a normal battery supply voltage.
• For safety reasons, keep the volume of your audio system moderate so that you
can still hear normal traffic sounds in a reasonable distance.
WIRING INSTRUCTIONS
POWER CONNECTION
The battery terminal (BATT ) must be connected directly to the positive terminal of
the vehicle battery to provide an adequate voltage source and minimize noise.
Connecting the battery terminal lead to any other point (such as the fuse block)
will reduce the power output and may cause noise and distortion. Use only #12
gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal
of the battery after all other wiring is completed.
GROUND CONNECTION
The ground terminal (GND) connection is also critical to the correct operation of
the amplier. Use a wire of the same gauge as the power connection (#8 or thicker)
and connect it between the ground terminal (GND) of the amplier and a metal
part of the vehicle close to the mounting location. This wire should be as short as
possible and any paint or rust at the grounding point should be scraped away to
provide a clean metal surface to which the end of the ground wire can be screwed
or bolted.
Produkt Specifikationer
| Mærke: | Pyle |
| Kategori: | Modtager |
| Model: | PLUTV42CH.5 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Pyle PLUTV42CH.5 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Modtager Pyle Manualer
3 Juni 2025
13 Januar 2025
6 December 2024
6 December 2024
22 September 2024
20 September 2024
6 September 2024
5 September 2024
3 September 2024
1 September 2024
Modtager Manualer
- Music Hall
- Fishman
- Musical Fidelity
- Vaddio
- Naxa
- Sonance
- ESX
- Thomson
- Mac Audio
- Roland
- Sencor
- PAC
- Hegel
- Audient
- PureLink
Nyeste Modtager Manualer
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
16 Juni 2025
16 Juni 2025