Pyramid Time Systems 9D26BRCT Manual

Pyramid Time Systems digital tidsafbryder 9D26BRCT

Læs gratis den danske manual til Pyramid Time Systems 9D26BRCT (4 sider) i kategorien digital tidsafbryder. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Pyramid Time Systems 9D26BRCT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

TIMETR NC COUNT UP/COUNTDOWN AX SY ™

DIGITAL TIMER CONTROLLER

Model CTPLATEBUZ/CBPLATEBUZ Instr tio s uc ns

888 726.479. 4

p ami esystem.com yr dtim

I22 Rev. C 64

OVERVIEW

The Tim r Sync Count Up/Down or Code Blue ControllereT ax ™ is used in conjunction with a TimeTrax Sync™ Digital

Timer (sold separately) to monitor elapsed or remaining time during critical events, educational testing/instruction,

manufacturing processes, lab testing, recreational activities, seminars, transportation depot applications, broadcasting and

other time-sensitive events. Features include a Start/Pause button to start or stop counting function. A built-in buzzer

signals the user when timer reaches zero in countdown mode.

Use Count Up/Countdown or Code Blue Controller with any of the following TimeTrax Sync™ Digital Timer models:

9D26BRCT, S9D2R6CALS, S9D4R6CALB, S9D2B6CALB, S9D2R6CAUB, S9D4R6CAUB, S9D2B6CAUB, S9D4B6CAUB.

TimeTrax Sync™ Digital Timers may also be used in conjunction with a TimeTrax Sync™ RF Wireless Transmitter to

receive accurate, official time signal.

Connect RJ45 cable into port located in compartment on back of Controller switch plate.

Route the RJ45 cable through standard single gang electrical box (not included). Pull cable through wall

cavity and out to digital timer installation location.

Plug other end of RJ45 cable into port located in compartment on back of TimeTrax Sync™ Digital

Tim er (sold separately). The Controller switch plate is able to control more than one Digital Timer.*

Wire TimeTrax Sync™ Digital Timer according to installation instructions.

CAUTION: 110V CLOCK WIRING SHOU BE COMP T P ELECTRICAL LD LE ED ER CODE AND P RM BY A LICENSED ELECTRI AN.ERFO ED CI

Before mounting controller switch plate to electrical box, push the buzzer volume test button located on

the back of switch plate in the top right hand corner.

To increase buzzer volume, turn blue volume control button clockwise using a flathead screwdriver. To

decrease buzzer volume or deactivate buzzer, turn blue volume button counter clockwise.

To enable “pulsating” buzzer sound, remove jumper from J2 and install jumper on J1.

Mount Controller switch plate to electrical box using two screws provided.

*Use RJ45 Y-Splitter (part no 41270) to daisy chain more than one digital timer.

INSTALLATION

TIMETR NC COUNT UP/COUNTDOWN AX SY ™

DIGITAL TIMER CONTROLLER

Model CTPLATEBUZ/CBPLATEBUZ Instr tio s uc ns

888 726.479. 4

p ami esystem.com yr dtim

I22 Rev. C 64

To start COUNT UP, push red button. Timer counts up from 00:00:00 to 99:59: . START/PAUSE 59

To pause during COUNT UP, push red START/PAUSE button. Timer stops counting.

Push red START AUSE/P button again to restart COUNT UP.

To , push RESET SET HR SET MIN and buttons at same time. The counter displays 88:88:88. If used in

conjunction with a TimeTrax Sync™ RF Wireless Transmitter, the timer will display current time.

To activate COUNTDOWN, push either SET HR SET MIN or button. Timer displays 00:00:00.

Push SET HR and/or SET MIN to change display to desired starting time.

To start COUNTDOWN, push red button. Timer counts down from desired hours/minutes START/PAUSE

and buzzer sounds at completion of time interval.

To pause during COUNTDOWN, push red button. Timer stops counting. START/PAUSE

To stop buzzer, push SET HR SET MIN or button.

Push red START/PAUSE button again to restart COUNTDOWN.

To , push RESET SET HR SET MINand buttons at the same time. The counter displays 88:88:88. If used in

conjunction with a TimeTrax Sync™ RF Wireless Transmitter, the timer will display time.

NOTE: In countdown mode, timer will count to negative 99:59:59. Timer will display “-“ symbol for first 10 hours. Display flashes

when counting negative.

S CIFIC IOPE AT NS

COUNT UP MODE OPERATION

COUNTDOWN MODE OPERATION

Produkt Specifikationer

Mærke:	Pyramid Time Systems
Kategori:	digital tidsafbryder
Model:	9D26BRCT
Vekselstrømsindgangsspænding:	105-240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	285.75 mm
Dybde:	38.1 mm
Højde:	114.3 mm
Vægt:	771 g
Produktfarve:	Sort
Skærmtype:	Digital
Skærmteknologi:	LED
Driftstemperatur (T-T):	-20 - 45 °C
Husmateriale:	Acrylonitrilbutadienstyren
Certificering:	UL, cUL