Robbe ARCUS II NIGHT Manual

Robbe Radiostyret legetøj ARCUS II NIGHT

Læs gratis den danske manual til Robbe ARCUS II NIGHT (24 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Robbe ARCUS II NIGHT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

INSTRUCTIONS AND USER MANUAL

www.robbe.com

V1_05/2019

Standard Version No.: 2649

Night Version No.: 2650

RTF Version No.: 2651

ENGLISH

INSTRUCTIONS AND USER MANUAL

GENERAL INFORMATION

• The model is designed for the components specied by us. Unless otherwise stated, servos and

other electronic components are designed for standard supply voltage. Recommended cell

count for Lipo batteries also refers to standard Lipos voltage of 3.7V per cell. If you use other ser-

vos, a different motor and controller, batteries, or propellers, please make sure they t rst. In the

event of deviations, corrections and adjustments must be made by yourself.

• Before starting construction, always put the servos into neutral. To do this, switch on the remo-

te control and move the joysticks and trim buttons (save the one for the throttle) to the middle

position. Connect the servos to the corresponding outputs of the receiver and supply them with a

suitable power source. Please observe the connection diagram and the operating instructions of

the remote control system manufacturer.

• Do not leave your model in the blazing sun or in your vehicle for long periods of time. Too high

temperatures can lead to deformation/distortion of plastic parts or blistering of covering foils.

• Before the rst ight, check the wing symmetry, tail unit and fuselage. All parts of the model should

have the same spacing from the left and right wing or tail plane to the centre of the fuselage or

the same angle.

• If necessary, rebalance the propellers if vibrations are noticeable when the motor is running up.

• Bubble formation in the covering foils normal to a certain extent due to temperature and humidity

differences and can be easily eliminated with a foil iron or hairdryer.

• For models in shell construction („full GFRP/CFRP“), burrs may occur at the seams due to the pro-

duction process. Carefully remove them with ne sandpaper or a le.

SAFETY INSTRUCTIONS FOR CONTROLLERS

GENERAL SAFETY INFORMATION

• Be sure to read the safety instructions carefully before operating your model.

• Always follow the procedures and settings recommended in the instructions.

• If you are using remote-controlled model aircraft, helicopters, cars or ships for the rst time, we

recommend that you ask an experienced model pilot for help.

• Remote-controlled models are not toys in the usual sense and may only be used and operated by

young people under 14 years of age under the supervision of adults.

• Their construction and operation requires technical understanding, careful craftsmanship and

safety-conscious behaviour.

• Mistakes or negligence during construction, ying or driving can result in considerable damage to

property or personal injury.

• Since the manufacturer and seller have no inuence on the proper construction/assembly and

operation of the models, these risks are expressly pointed out and any liability is excluded.

• Propellers on aircraft and all moving parts in general pose a constant risk of injury. Avoid touching

such parts at all costs.

• Note that motors and controllers can reach high temperatures during operation. Avoid touching

such parts at all costs.

• Never stay in the danger area of rotating parts with electric motors with connected drive battery.

• Overcharging or incorrect charging can cause the batteries to explode. Make sure the polarity is

correct.

• Protect your equipment and Models from dust, dirt and moisture. Do not expose the equipment to

excessive heat, cold or vibration.

• Use only recommended chargers and charge your batteries only up to the specied charging

time. Always check your equipment for damage and replace defects with original spare parts.

• Do not use equipment that has been damaged or got wet due to a fall, even if it is dry again!

Either have it checked by your specialist dealer or in the Robbe Service or have it replaced.

Hidden faults can occur due to wetness or a crash, which lead to a functional failure after a short

operating time.

• Only the components and accessories recommended by us may be used.

• Do not make any changes to the remote control which are not described in these instructions.

• Observe the technical data of the controller.

• Observe the polarity of all connection cables.

• Avoid short circuits at all costs.

• Install or package the regulator so that it cannot come into contact with grease, oil or water.

• Ensure adequate air circulation.

• Never reach into the turning circle of the propeller during start-up Risk of injury

Important information:

The receiver system is powered by the built-in BEC system of the controller.

For commissioning, always move the throttle stick to the „Motor off“ position and switch on the

transmitter. Only then connect the battery. To switch off always disconnect the connection battery

motor controller, rst

then turn off the transmitter. During the functional test, move the servos of the rudders to neutral

position with the remote control (stick and trimming lever on the transmitter to the middle position).

Please make sure to leave the throttle stick in the lowest position so that the engine does not start.

For all work on

to the parts of the remote control, motor or controller, follow the instructions supplied with the units.

Also read the instructions of the battery and the charger carefully before commissioning.

Check the engine mounting bolts in the fuselage regularly for tightness.

SAFETY NOTE FOR MODEL OPERATION

Attention, danger of injury!

• Always keep a safe distance from your model aircraft.

• Never y over spectators, other pilots or yourself.

• Always perform ight gures in a direction away from the pilot or spectators.

• Never endanger people or animals.

• Never y near power lines or residential areas.

• Do not operate your model near locks or public shipping.

• Do not operate your model on public roads, motorways, paths and squares, etc., but only in

approved locations.

• Do not operate the model in thunderstorms.

• Before each ight, check your remote control system for sufcient function and range.

• After ying, remove all batteries from the model.

Do not „aim“ the transmitter antenna at the model during operation. In this direction, the transmitter

has the lowest radiation. The best position of the antenna is to the side of the model.

Use of devices with image and/or sound recording function:

If you equip your model with a video or image recording device (e.g. FPV cameras, action scams

etc.) or the model is already equipped with such a device at the factory, please note that you

could violate the privacy of one or more persons by using the recording function. An overight or

driving on private ground without the appropriate permission of the owner or approaching private

ground can also be regarded as an invasion of privacy. You, as the operator of the model, are sole-

ly and fully responsible for your actions.

In particular, all applicable legal requirements must be observed, which can be found in the roof

associations or the relevant authorities. Failure to comply can result in substantial penalties.

Produkt Specifikationer

Mærke:	Robbe
Kategori:	Radiostyret legetøj
Model:	ARCUS II NIGHT
Vægt:	850 g
Brugervejledning:	Ja
Produktfarve:	Black, Red, White
Motortype:	Børstefri
Produkttype:	Svæveflyver
Husmateriale:	Carbon, Carbon Fibre Reinforced Polymer (CFRP), Expanded Polyolefin (EPO), Foam, Plastic
Længde:	1190 mm
Antal kanaler:	4 kanaler
Konstruktionstype:	Plug-N-Play (PNP)
Vingefang:	1840 mm
Sværhedsgrad:	Begynder
Anbefalet batteri:	3S/1300mAh LiXX
Antal servodrev:	4
Servo vægt:	8 g