Roland C-280 Manual

Roland Ikke kategoriseret C-280

Læs gratis den danske manual til Roland C-280 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Roland C-280, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Classic Organ Date: Oct. 1. 1999

Model: C-280

MIDI IMPLEMENTATION

Version: 1.00

1. Receive data

■

Channel Voice Messages

●

Note o

Status 2nd byte 3rd byte

8nH kkH vvH

9nH kkH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

kk = note number: 00H-7FH (0-127)

vv = note o velocity: 00H-7FH (0-127)

●

Note on

Status 2nd byte 3rd byte

9nH kkH vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

kk = note number: 00H-7FH (0-127)

vv = note on velocity: 01H-7FH (1-127)

* Note numbers outside the range of 18-113 are transposed to the nearest octave within

this range.

* Transpose function does not aect the recognized note numbers.

●

Control Change

* The value specied by a Control Change message will not be reset even by a Program

Change, etc.

❍

Data Entry (Controller number 6, 38)

Status 2nd byte 3rd byte

BnH 06H mmH

BnH 26H llH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm, ll = the value of the parameter specied by RPN

* Data entry messages are recognized only when received on the basic channel.

❍

Volume (Controller number 7)

Status 2nd byte 3rd byte

BnH 07H vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Volume: 00H-7FH (0-127), Initial Value = 7FH (127)

❍

Expression (Controller number 11)

Status 2nd byte 3rd byte

BnH 0BH vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Expression: 00H-7FH (0-127), Initial Value = 7FH (127)

❍

Hold 1 (Controller number 64)

Status 2nd byte 3rd byte

BnH 40H vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON

❍

RPN MSB/LSB (Controller number 100, 101)

Status 2nd byte 3rd byte

BnH 65H mmH

BnH 64H llH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm = upper byte of parameter number specied by RPN

ll = lower byte of parameter number specied by RPN

* The value specied by RPN will not be reset even by messages such as Program Change

or Reset All Controller.

* RPN messages are recognized only when received on the basic channel.

**RPN**

The RPN (Registered Parameter Number) messages are expanded control changes, and each

function of an RPN is described by the MIDI Standard.

To use these messages, you must rst use RPN MSB and RPN LSB messages to specify the

parameter to be controlled, and then use Data Entry messages to specify the value of the

specied parameter. Once an RPN parameter has been specied, all Data Entry messages

received on that channel will modify the value of that parameter. To prevent accidents, it is

recommended that you set RPN Null (RPN Number = 7FH/7FH) when you have nished

setting the value of the desired parameter.

On the C-280, RPN can be used to modify the following parameters.

RPN Data entry

MSB LSB MSB LSB Explanation

00H 01H mmH llH Master Fine Tuning

mm, ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99.99

cents), Initial Value = 40 00H (± 0 cent)

7FH 7FH --- --- RPN null

Set condition where RPN and NRPN are

unspecied. The data entry messages after set

RPN null will be ignored.

(No Data entry messages are required after RPN

null).

Settings already made will not change.

mm, ll: ignored

●

Program Change

Status 2nd byte

CnH ppH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

pp = Program number: 00H..37H (prog.1..prog.56)

Received program change message are assigned as follows.

prog. tone

1 Organ Manual

2 Ensemble Chime

3 Ensemble Celesta

4 Ensemble Choir

17 Ensemble Chime + Organ Manual

33 Ensemble Celesta + Organ Manual

49 Ensemble Choir + Organ Manual

* “+” indicatesadualtone.'

* Program numbers not in the above table are ignored.

* The switch to the requested Ensemble Tone is made when the rst new Note On

message arrives after the Program Change has been received. Organ Tones are changed

immediately after reception of the Program Change.

* When the C-280 receives Program Change messages that include requests for Organ

Tones, the [Manual] button is selected.

* Organ Tones are set by mean of Program Changes, and System Exclusive messages that

indicate the status of Draw knobs.

For more information about the System Exclusive messages that indicate the status of

Draw knobs, refer to "3. Parameter Address Map."

■

Channel Mode Messages

●

Reset All Controllers (Controller number 121)

Status 2nd byte 3rd byte

BnH 79H 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* When this message is received, the following controllers will be set to their reset values.

Controller Reset value

Expression 127 (max)

Hold 1 0 (o)

RPN unset; previously set data will not change

●

Local Control

Status 2nd byte 3rd byte

BnH 7AH vvH

n=MIDI channel number: 0H - FH (ch.1 - ch.16)

vv=Value: 00H, 7FH (0, 127) 0=OFF 127=ON

●

All Notes O (Controller number 123)

Status 2nd byte 3rd byte

BnH 7BH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* When All Notes O is received, all notes on the corresponding channel will be turned

o. However if Hold 1 is ON, the sound will be continued until these are turned o.

●

OMNI OFF (Controller number 124)

Status 2nd byte 3rd byte

BnH 7CH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* The same processing will be carried out as when All Notes O is received.

●

OMNI ON (Controller number 125)

Status 2nd byte 3rd byte

BnH 7DH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* The same processing will be carried out as when All Notes O is received.

●

MONO (Controller number 126)

Status 2nd byte 3rd byte

BnH 7EH mmH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm = mono number: 00H-10H (0-16)

* The same processing will be carried out as when All Notes O is received.

●

POLY (Controller number 127)

Status 2nd byte 3rd byte

BnH 7FH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* The same processing will be carried out as when All Notes O is received.

■

System Realtime Message

●

Active Sensing

Status

FEH

* When Active Sensing is received, the unit will begin monitoring the intervals of all

further messages. While monitoring, if the interval between messages exceeds 380 ms,

the same processing will be carried out as when All Notes O and Reset All Controllers

are received, and message interval monitoring will be halted.

■

System Exclusive Message

Status Data byte Status

F0H iiH, ddH, ......,eeH F7H

F0H: System Exclusive Message status

ii = ID number: an ID number (manufacturer ID) to indicate the manufacturer whose

Exclusive message this is. RolandsmanufacturerIDis41H.'

ID numbers 7EH and 7FH are extensions of the MIDI standard;

Universal Non-realtime Messages (7EH) and Universal Realtime

Messages (7FH).

dd,...,ee = data: 00H-7FH (0-127)

F7H: EOX (End Of Exclusive)

The System Exclusive Messages received by the C-280 are; Universal Non-realtime System

Exclusive messages, and Data Set (DT1).

●

Universal Non-realtime System Exclusive Messages

❍

Identity Request Message

Status Data byte Status

F0H 7FH, dev, 06H, 01H F7H

Byte Explanation

FOH Exclusive status

7FH ID number (universal non-realtime message)

dev Device ID (dev: UNIT#-1)

06H Sub ID#1 (General Information)

01H Sub ID#2 (Identity Request)

F7H EOX (End Of Exclusive)

* The "dev" is own device number (UNIT#-1) or 7FH (Broadcast).

* UNIT# is always the same as the current basic channel.

●

Data transmission

C-280 can transmit and receive the various parameters using System Exclusive messages.

The exclusive message of C-280 data has a model ID of 1AH, and device ID is dened by

MIDI UNIT NUMBER. UNIT NUMBER is always the same as the current basic channel.

❍

Data set 1 DT1

This is the message that actually performs data transmission, and is used when you wish to

transmit the data.

Status Data byte Status

F0H 41H, dev, 1AH, 12H, aaH, bbH, ccH, sum F7H

Byte Explanation

F0H Exclusive status

41H ID number (Roland)

dev Device ID (dev: UNIT#-1)

1AH Model ID (C-280)

12H Command ID (DT1)

aaH Address MSB: upper byte of the starting address of the transmitted data

bbH Address LSB: lower byte of the starting address of the transmitted data

ccH Data: the actual data to be transmitted.

sum Checksum

F7H EOX (End Of Exclusive)

* If "Data Set 1" is transmitted successively, there must be an interval of at least 40 ms

between packets.

* Regarding the address please refer to section 3 (Parameter Address Map).

* Regarding the checksum please refer to section 4 (Supplementary material).

Produkt Specifikationer

Mærke:	Roland
Kategori:	Ikke kategoriseret
Model:	C-280

Har du brug for hjælp?

Hvis du har brug for hjælp til Roland C-280 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Roland Manualer

Roland SRX KEYBOARDS Manual

3 August 2025

Roland R-88 Manual

3 August 2025

Roland GALAXIAS Manual

3 August 2025

Roland SRX DANCE TRAX Manual

3 August 2025

Roland TR-808 Manual

3 August 2025

Roland SRX ELECTRIC PIANO Manual

3 August 2025

Roland SRX WORLD Manual

3 August 2025

Roland SRX PIANO II Manual

2 August 2025

Roland SRX BRASS Manual

2 August 2025

Roland PM-3 Manual

2 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

YSI T-1 Manual

16 August 2025

Extron HC 403 Manual

16 August 2025

Advantech DS-082 Manual

16 August 2025

Pentatech KA20 Manual

16 August 2025

Advantech WOP-215K-NAE Manual

16 August 2025

Emerson CKSS7801WM Manual

16 August 2025

MSW -FMP-01 Manual

16 August 2025

Vulcan VICM24 Manual

16 August 2025

HP Elite Mini 805 G8 Manual

16 August 2025

TP-Link LS106P Manual

16 August 2025