Roland HT-TX01 Manual

Roland AV forlænger HT-TX01

Læs gratis den danske manual til Roland HT-TX01 (2 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Roland HT-TX01, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Before using this unit, carefully read the sections entitled “USING THE UNIT SAFELY” and “IMPORTANT NOTES”

on back side. These sections provide important information concerning the proper operation of the unit.

Additionally, in order to feel assured that you have gained a good grasp of every feature of your new unit, read

Owner's Manual in its entirety. This manual should be saved and kept on hand as a convenient reference.

Owner’s Manual

RS-232 Connector (RS-232 Conversion Cable) Specications

D-sub 9-pin (male)

12345

6789

3.5mm miniature

phone plug

TXD

RXD

GND

Pin No. Signal

1 N.C.

2 RXD

3 TXD

4 N.C.

5 GND

6 N.C.

7 N.C.

8 N.C.

9 N.C.

Communication method Synchronous (asynchronous), full-duplex

Communication speed 9600 bps, 19200 bps, 38400 bps, 115200 bps

Parity none

Data length 8 bit

Stop bit 1 bit

Code set ASCII

Flow control none

Cable Wiring Diagram

When using the included RS-232 conversion cable, RXD, TXD, and GND are wired as shown below.

Unit end

(conversion cable end) Controller end

N.C. : 1 1 :

RXD : 2 2 : RXD

TXD : 3 3 : TXD

N.C. : 4 4 :

GND : 5 5 : GND

N.C. : 6 6 :

N.C. : 7 7 :

N.C. : 8 8 :

N.C. : 9 9 :

* When you want to extend the RS-232 conversion cable, use a straight cable.

Attaching the Ferrite Cores

1. Open an included ferrite core by spreading apart the tabs at two places.

2. Attach the ferrite core to an HDMI cable, LAN cable, or RS-232 conversion cable.

* Close the ferrite core by pressing down on each tab until it clicks into place.

Attach near the base of the plug at

the end that connects to the unit.

Connection Examples

* For a connection to the HDBaseT connector, use a Cat5e (Category 5e) or higher shielded LAN cable.

* *For a connection to the RS-232 connector, use the included RS-232 conversion cable.

HDMI INPUT

connector

RS-232

connector

RS-232-compatible

projector, etc.

RS-232-compatible

device (computer, etc.)

Displays,

projectors, etc.

Roland XS series device, etc.

HT-RX01

HDBaseT OUTPUT

connector

RS-232

connector

RS-232

connector

RS-232

connector

RS-232-compatible

device (computer, etc.)

Displays,

projectors, etc.

Roland V-40HD device, etc.

HT-RX01

HT-TX01

RS-232

connector

HDMI INPUT

connector

HDMI OUTPUT

connector

Panel Descriptions

HT-TX01 (Transmitter)

1 2 3 * These connectors are not used.

4 5 6

HT-RX01 (Receiver)

1 2 7 * These connectors are not used.

4 8 6

No. Name Explanation

1 Power indicator This lights up when power is supplied.

2 LINK indicator This lights up when the transmitter/receiver is correctly connected

3 HDMI INPUT connector The HDMI signal from the source device is input here.

4 AC adaptor connector This is for connecting the included AC adaptor.

No. Name Explanation

5 HDBaseT (TX) connector This is for connecting a receiver.

6 RS-232 connector This is for connecting a remote-control device (RS-232-compatible

computer, projector, or the like) using the included RS-232 conversion cable.

7 HDMI OUTPUT connector This outputs the HDMI signal to a display device.

8 HDBaseT (RX) connector This is for connecting a transmitter, Roland XS series unit, or other such

device.

Main FeaturesChecking the Included Items

• The unit

• AC adaptor, insertion plugs (3 types)

• RS-232 conversion cable (2 m)

• Ferrite core x 3

• Owner’s Manual (this document)

This unit is a transmitter/receiver for long-distance transmission of HDMI signals over up to 100 meters using a single LAN cable (Cat5e or higher).

• Support for 1080/59.94p (full HD) and 3D video

• Support for HDMI 1.4 and HDCP 2.0

• Support for RS-232 signals

Attaching an AC Adaptor Insertion Plug

1. Attach an included AC adaptor insertion plug to the AC adaptor.

* Attach the insertion plug for your country or region.

* Attach the insertion plug by pressing it in until it clicks into place.

* Be sure always to use the included AC adaptor with the unit.

To detach, pull out the insertion plug

while squeezing the left and right

sides of the lock section inward.

Main Specications

Input Formats 480/59.94i, 576/50i, 480/59.94p, 576/50p, 720/59.94p, 720/50p,

1080/59.94i, 1080/50i, 1080/59.94p, 1080/50p, 640 x 480, 800 x 600,

1024 x 768, 1280 x 768, 1280 x 1024, 1366 x 768, 1400 x 1050,

1600 x 1200, 1920 x 1200

* RGB formats : Conforms to VESA DMT Version 1.0 Revision 11.

* The maximum refresh rates of RGB is 75 Hz. (excluding 1600 x 1200

and 1920 x 1200. The refresh rate of these 2 is 60Hz)

* 1920 x 1200/60Hz : Reduced blanking

* Also check the supported resolutions of the connected device.

Audio Formats The maximum is PCM 8ch, Dolby Digital, True HD DTS-HD Master Audio

Input Connectors HT-TX01 HDMI x 1: Type A 19 pins

HT-RX01 RJ45 x 1

Output Connectors HT-TX01 RJ45 x 1

HT-RX01 HDMI x 1: Type A 19 pins

Other Connectors RS-232 x 1: 9 pins D-sub type * When using additional RS-232 cable.

Transmission distance The maximum is 100 m (328 ft)

* The available distance depends on the quality of the LAN cable.

Operating temperature range 0 to 40 degree C

32 to 104 degrees F

Operating temperature humidity 10 to 85 % (no condensation)

Storage temperature range -20 to 60 degree C

-4 to 140 degrees F

Storage temperature humidity 10 to 85 % (no condensation)

Power Supply AC Adaptor

Current Draw 2 A

Dimensions 81 (W) x 93 (D) x 24 (H) mm

3-3/16 (W) x 3-11/16 (D) x 1 (H) inches

Weight excl. AC adaptor 300 g

11 oz

* In the interest of product improvement, the specications and/or appearance of this unit are subject to

change without prior notice.

Dimensions

any form without the written permission of ROLAND CORPORATION.

For China

For EU Countries

*5100044591- 01*

24.9

73.4

Produkt Specifikationer

Mærke:	Roland
Kategori:	AV forlænger
Model:	HT-TX01

Har du brug for hjælp?

Hvis du har brug for hjælp til Roland HT-TX01 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

AV forlænger Roland Manualer

Roland HT-TX01 Manual

19 Juli 2024

Roland HT-RX01 Manual

13 Oktober 2022

AV forlænger Manualer

Nyeste AV forlænger Manualer

EtherWAN ED3538 Manual

30 Oktober 2025

Kramer TP-120-OD Manual

21 Oktober 2025

Kramer VM-218DT Manual

17 Oktober 2025

Kramer KIT-401 Manual

16 Oktober 2025

Kramer TP-580CT Manual

16 Oktober 2025

CYP PUV-1230PL-KIT Manual

15 Oktober 2025

Smart-AVI DVX-RXPROS Manual

13 Oktober 2025

Extron FOX3 SR 211 Manual

10 Oktober 2025

Extron FOX3 T 211 Manual

8 Oktober 2025

Blustream HEX100ARC-KIT Manual

6 Oktober 2025