Roland KD-200-MS Manual

Roland Ikke kategoriseret KD-200-MS

Læs gratis den danske manual til Roland KD-200-MS (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Roland KD-200-MS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Check the Included Items

After opening the package, check that all of the included items

are present. If anything is missing, contact your dealer.

Main unit

Wood hoop protector × 2

Connection cable

Drum key

Owner’s manual

* This package does not include a kick pedal or beater. A variety of

commercially available beaters can be used, including felt, plastic, or

wood types. However, if you use a felt beater, strike marks of the felt

might remain on the striking surface.

Descriptions

Front head

Hoop

Leg

fastener

knob

Rod

Foot nut

Foot

Leg

Shell

Tension bolt

Lug

Batter head’s strike surface

Batter board stopper

Hook

Batter board

Batter head

(inside)

TRIGGER OUT jack

Batter hoop

* Do not insert your hand or ngers into the gap between the batter

board and the batter head striking surface. Doing so might cause

injury, damage, or malfunction.

Assembling the KD-200

NOTE

During assembly, take care that the weight of the bass drum does not

pinch your hand or foot.

1. Loosen the leg fastener knob, adjust the angle of

the leg, and then tighten the leg fastener knob.

Using a drum key, adjust the length of the rods so that

the left and right are the same length.

Leg fastener knob

rod

2. Adjust the tip of the legs (spike/rubber)

appropriately for the surface on which you’re

placing the KD-200.

Spike Soft oor

Carpet, etc.

Rubber Hard oor

Wood ooring, concrete, etc.

If you loosen the foot nut and rotate the foot to raise it,

the spike will be exposed.

Tighten the foot nut to secure the position of the foot.

Foot nut

Foot

Spike

Spike Rubber

* The tip of the spike is sharp; handle it with care.

* Using the spike leg tips on wood ooring may damage the oor; the

rubber leg tips should be used on wood ooring.

3. Ax the wood hoop protectors to the position

at which the kick pedal is attached.

Ax to both surfaces of

the batter hoop

4. Mount the kick pedal.

Adjust the location at which the kick pedal is attached

so that the beater strikes the center of the batter head’s

strike surface; then securely fasten the kick pedal to the

KD-200.

* Take care not to pinch your ngers.

the center of Beater must hit

the striking surface

After attaching the kick

pedal, adjust the angle of

the legs and the length of

the rods as necessary.

Using Double Kick Pedals

The KD-200 can also be used with double kick pedals.

Adjust the striking points of the two beaters so that they are at

equal distances to the left and right of the batter head’s strike

surface.

Correct Incorrect

If the beater’s striking point cannot be aligned appropriately

Depending on the kick pedal, it might not be possible to attach

it to the bass drum so that the strike point of the two beaters is

located symmetrically to the left and right of the center of the

batter head’s strike surface.

In this case, use the following procedure to adjust the position of

the batter head’s strike surface.

1. Remove all of the hooks/tension bolts, the batter

board stopper, and the batter hoop.

Batter board

Batter board stopper

Tension bolt

Hook

Batter head

Batter hoop

NOTE

To avoid injury, damage, or malfunction, do not detach the batter

board and batter head from the shell. Take care not to injure your

hands or feet while working.

2. Turn the batter head together with the batter

board, and adjust it so that the center of the

TRIGGER OUT jack is near the location shown in

the illustration.

Batter board

Batter head

(approximate)

3. Place the batter hoop back.

4. Attach the batter board stopper to the hooks/

tension bolts.

Hook / Tension bolt

Batter board stopper

5. Alternating between opposite sides and using

your ngers to press the hooks and batter board

stoppers A, insert the tension bolts into the lugs

while pressing the batter board stoppers A in

between the batter hoop B and the batter board

Batter board stopper A

Batter board C

Batter hoop B

Push down

6. Working alternately across opposite sides of the

drum, lightly tighten each tension bolt until the

hooks do not wobble.

7. Then tighten each tension bolt another 3/4 of a

turn to secure the front head.

* If the batter head is not secured suciently, the sensor might

malfunction, or the sound of the strike might be too loud.

Connecting to the Drum Sound Module

Connect the KD-200 to your drum sound module.

Use the included connection cable to make the connection.

Connect the “L” plug of the connection cable to the jack of the

KD-200.

(Example) TD-50

“I” plug KICK

“L” plug

Recommended Parameter Settings

These are the recommended values for the trigger parameters

when using the KD-200 with various drum sound modules.

If the “PAD TYPE” or “TRIG TYPE” of your drum sound module

provides a “KD200” setting, choose “KD200.” If “KD200” is not one

of the available values, refer to the support information on the

Roland website.

http://roland.cm/trigger_prm

You may need to adjust the trigger parameters depending on

how you’ve mounted the KD-200 and the location at which

you’ve installed it.

For details on editing refer to the owner’s manual of your drum

sound module.

Adjusting the Head Tension

Adjust the tension of the batter head before you play the KD-200.

You can vary the strike response (playing feel) by adjusting the

tension.

1. Adjust each tension bolt little by little, working

back and forth across the head in the order

shown in the illustration.

Batter head

Tension bolt

* Fully tightening a tension bolt at only a single location will produce

uneven tensioning, which will make it impossible to achieve correct

strike response and may also cause malfunctions.

2. Adjust each tension bolt so that the head is

tensioned evenly.

Main Specications

Roland KD-200: Bass drum

Shell 20 (Diameter) x 16 (Depth) inches

Wood shell

Trigger 1 (Head)

Acceptable

pedal Single pedal, Twin pedal

Connector TRIGGER OUT jack

Dimensions

633 (W) ×507 (D) ×528 (H) mm

24-15/16 x 20 x 20-13/16 inches

*When storing the legs

Weight 10.9 kg

24-15/16 x 20 x 20-13/16 inches

* This document explains the specications of the product at the time

that the document was issued. For the latest information, refer to the

Roland website.

Before using this unit, carefully read the leaet “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the

document(s) where it will be available for immediate reference.

English

Owner’s Manual

KD-200

* 5 1 0 0 0 6 8 8 0 4 - 0 1 *

Produkt Specifikationer

Mærke:	Roland
Kategori:	Ikke kategoriseret
Model:	KD-200-MS

Har du brug for hjælp?

Hvis du har brug for hjælp til Roland KD-200-MS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Roland Manualer

Roland SRX KEYBOARDS Manual

3 August 2025

Roland R-88 Manual

3 August 2025

Roland GALAXIAS Manual

3 August 2025

Roland SRX DANCE TRAX Manual

3 August 2025

Roland TR-808 Manual

3 August 2025

Roland SRX ELECTRIC PIANO Manual

3 August 2025

Roland SRX WORLD Manual

3 August 2025

Roland SRX PIANO II Manual

2 August 2025

Roland SRX BRASS Manual

2 August 2025

Roland PM-3 Manual

2 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Alpine IVA-C800R Manual

17 August 2025

ZyXEL XGS1935-28 Manual

17 August 2025

Alpine TUE-T200DVB Manual

17 August 2025

Royal Catering RC-SGI01 Manual

17 August 2025

Crelando HG06256E Manual

17 August 2025

Nabo FK 2570 Manual

17 August 2025

Primo PR164RKZ Manual

17 August 2025

IFM CR1142 Manual

17 August 2025

Hartke Bass Attack 2 Manual

17 August 2025

Ferroli TP3 COND 65÷1000 Manual

16 August 2025