Roland MDS-Compact Manual

Roland Ikke kategoriseret MDS-Compact

Læs gratis den danske manual til Roland MDS-Compact (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Roland MDS-Compact, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

5. Attaching the pad mounts

The tips of the mounts are sharp. Handle them with care.

5–1. Place the stand upright, then loosen the hand knobs

of holders “A” and “B” (two places). Next, spread open

the pipes at left and right.

5–2. Verify that the four vertical pipes are truly vertical.

If the stand wobbles, loosen the bolts on the

holders of curved pipes “L” and “R,” and adjust the

height. After adjusting the height, tighten the

bolts on the holders.

Hand knobs

Holder bolts

5–3. Attach mount holders to the top of the stand and

tighten the respective hand knobs.

Mount holder Mount holder

Hand knobs

5–4. Attach the pad mounts to mount holder, and rmly

tighten the respective hand knobs.

Pad mount

Hand knobs

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the document(s)

where it will be available for immediate reference.

Roland and V-Drums are registered trademarks of Roland Corporation in the United States and/or other countries.

Owner’s Manual

NOTE

• When setting-up or adjusting the stand, take care not to pinch your ngers between movable parts and the main unit. If using this in a location where children are present, be sure to provide adult supervision or guidance.

• Prepare an area in which you can perform the assembly safely.

• Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.

* If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat (TDM series) made by Roland to prevent the rubber feet from soiling the surface on which they are placed.

1. Check the parts

4 5 6 11

No. Name Quantity

1Stand 1

2Curved pipe L 1

3Curved pipe R 1

4Straight pipe L (Long) 1

5Straight pipe R (Short) 1

6Snare pipe 1

7Mount holder 3

8Pad mount 3

9Pad mount (ball type) 1

10 Cymbal mount (Short) 1

11 Cymbal mount (Long) 2

12 Drum key 1

13 Cable clip 4

14 Cable tie 2

2. Assembling the Left and Right Arm Sections

Lay the left and right arm sections on the oor while

assembling them.

2–1. Using a drum key, loosen the bolt on the holder of

straight pipe “L,” then insert curved pipe “L.”

Curved pipe L 2

Straight pipe L 4

Holder

Bolt

2–2. Attach mount holder to straight pipe “L.” Then, after

pulling down straight pipe “L” until it can move no

further, tighten the bolt.

Curved pipe L 2

Straight pipe L 4

Mount

holder

Holder

Bolt

2–3. Using a drum key, loosen the bolt on the holder of

straight pipe “R,” then insert curved pipe “R.”

Curved pipe R 3

Straight pipe R 5

7 cm

Holder

Bolt

2–4. Position straight pipe “R” so that its tip protrudes by

about 7 cm, and then tighten the holder.

3. Attach the Left and Right Arm Sections to

the Main Unit

3–1. Use a drum key to loosen bolt of the holder “A”

(attached to the left-side pipe (with two holders) of

the stand), and insert curved pipe “L” (of the assembly

you created in step 2-1–2-2) into holder “A” of the

stand.

Holder A

Bolt

Curved pipe L 2

Stand 1

As a general rule, insert curved pipe “L” until the

guide hole on the pipe can be seen through the

gap in the holder.

After rmly inserting it all the way, use the drum

key to rmly tighten bolt.

Drum key

Bolt

Guide hole

3–2. Lower holder “B” (attached to the right-side pipe

of the stand) to the same position as holder “C”

(attached to the left-side pipe of the stand).

Holder B

Holder C 7 cm

3–3. Use the drum key to loosen bolt of the holder “B,” and

insert curved pipe “R” (of the assembly you created in

step 2-3–2-4) into holder “B” of the stand.

Holder B

Bolt

Curved pipe R 3

As a general rule, insert curved pipe “R” until the

guide hole on the pipe can be seen through the

gap in the holder.

After rmly inserting it all the way, use the drum

key to rmly tighten bolt.

Guide hole Drum key

Bolt

4. Attaching the snare pipe

4–1. Use the drum key to loosen bolt of the holder “C,” and

insert the snare pipe into holder “C” of the stand. After

rmly inserting it all the way, use the drum key to

rmly tighten bolt.

Insert the end of the snare pipe that doesn’t have

a cap on it into holder “C.”

Holder C

Snare pipe 6

Cap

Bolt

Drum key

WARNING: Caution during setup

When setting-up, you must observe the following cautions.

If you fail to observe these cautions, the stand might overturn or fall, causing injury.

Check for stability when setting-up the stand, and take appropriate care.

Do not spread the stand wider

than 1.2 meters (48 inches).

1.2 m

Adjust the rod height so that

no part of any cymbal is higher

than 1.2 meters (48 inches)

above the oor.

1.2 m

Attach the cymbals in such

a way that the center of the

cymbal does not extend beyond

the rear pipes of the stand.

Center of cymbal must not

extend beyond rear of stand

5–5. Attach pad mount (ball type) to the snare pipe, and

tighten the hand knob.

Pad mount (ball

type) 9

Hand knob

6. Attaching the cymbal mounts

As appropriate for the drum kit that you’re using, attach

the cymbal mounts (short) to the locations for hi-hat

and ride cymbal.

6–1. Insert the two cymbal mounts and the hi-hat mount

into the holders of the curved pipes, and adjust all the

holders as shown in the illustration to complete setup.

“A” type (for hi-hat)

Pad mounts

Pad mount (ball type)

Cymbal mounts (Long)

Cymbal mounts (Short)

“B” type (for ride cymbal)

Pad mounts

Pad mount (ball type)

Cymbal mounts (Long)

Cymbal mounts (Short)

Notes

• When setting up or storing the stand, be careful

not to pinch the ngers you use to handle the

stand.

• Regarding the way of mounting a sound module,

pads, or cymbals, please refer to the owner’s

manual supplied with them.

Produkt Specifikationer

Mærke:	Roland
Kategori:	Ikke kategoriseret
Model:	MDS-Compact

Har du brug for hjælp?

Hvis du har brug for hjælp til Roland MDS-Compact stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Roland Manualer

Roland SRX KEYBOARDS Manual

3 August 2025

Roland R-88 Manual

3 August 2025

Roland GALAXIAS Manual

3 August 2025

Roland SRX DANCE TRAX Manual

3 August 2025

Roland TR-808 Manual

3 August 2025

Roland SRX ELECTRIC PIANO Manual

3 August 2025

Roland SRX WORLD Manual

3 August 2025

Roland SRX PIANO II Manual

2 August 2025

Roland SRX BRASS Manual

2 August 2025

Roland PM-3 Manual

2 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Alpine IVA-C800R Manual

17 August 2025

ZyXEL XGS1935-28 Manual

17 August 2025

Alpine TUE-T200DVB Manual

17 August 2025

Royal Catering RC-SGI01 Manual

17 August 2025

Crelando HG06256E Manual

17 August 2025

Nabo FK 2570 Manual

17 August 2025

Primo PR164RKZ Manual

17 August 2025

IFM CR1142 Manual

17 August 2025

Hartke Bass Attack 2 Manual

17 August 2025

Ferroli TP3 COND 65÷1000 Manual

16 August 2025