Roland VA-3 Manual

Roland Ikke kategoriseret VA-3

Læs gratis den danske manual til Roland VA-3 (20 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Roland VA-3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/20

VA-3 MIDI Implementation

The VA-3 implements additional functionality and parameters over and above the

G-1000, which itself was an expansion of the GS sound generator format. These func-

tions and parameters are marked by a [VA-3] symbol. If MIDI messages marked by a

VA-3 symbol are transmitted to another GS format sound generator or to the G-1000,

those messages may not be recognized.

1. Receive data

■

Channel Voice Messages

●

Note off

• For Drum Parts, these messages are received when Rx.NOTE OFF = ON for each

Instrument.

• The velocity values of Note O messages are ignored.

●

Note on

• Not received when Rx.NOTE MESSAGE = OFF. (Initial value is ON)

• For Drum Parts, these messages are not received when Rx.NOTE ON = OFF for

each Instrument.

●

Polyphonic Key Pressure

• Not received when Rx.POLY PRESSURE (PAf) = OFF. (Initial value is ON)

• The resulting eect is determined by System Exclusive messages. With the initial

settings, there will be no eect.

●

Control Change

• When Rx.CONTROL CHANGE = OFF, all control change messages except for

Channel Mode messages will be ignored.

• The value specied by a Control Change message will not be reset even by a Pro-

gram Change, etc.

❍

Bank Select (Controller number 0, 32)

• Not received when Rx.BANK SELECT = OFF.

• “Rx.BANK SELECT” is set to OFF by “GM1 System On,” and Bank Select messages

will be ignored.

• Rx.BANK SELECT is set to ON by “GM2 System On.”

• Rx.BANK SELECT is set to ON by power-on reset or by receiving “GS Reset.”

• When Rx.BANK SELECT LSB = OFF, Bank number LSB (llH) will be handled as 00H

regardless of the received value. However, when sending Bank Select messages,

you have to send both the MSB (mmH) and LSB (llH, the value should be 00H) to-

gether.

• Bank Select processing will be suspended until a Program Change message is re-

ceived.

• The GS format “Variation number” is the value of the Bank Select MSB (Controller

number 0) expressed in decimal.

• The VA-3 recognizes the Bank Select LSB (Controller number 32) as a ag for

switching between the VA-3 MAP, the G-1000 MAP, the G-800 MAP, and the SC-55

MAP. With a LSB of 01H, the SC-55 MAP and with a LSB of 02H, the G-800 MAP,

and with a LSB of 03H, the G-1000 MAP, and with a LSB of 04H, the VA-3 MAP will

be selected respectively.

• Some other GS devices do not recognize the Bank Select LSB (Controller number

32).

❍

Modulation (Controller number 1)

• Not received when Rx.MODULATION = OFF (Initial value is ON)

• The resulting eect is determined by System Exclusive messages. With the initial

settings, this is Pitch Modulation Depth.

❍

Portamento Time (Controller number 5)

• This adjusts the rate of pitch change when Portamento is ON or when using the Por-

tamento Control. A value of 0 results in the fastest change.

❍

Data Entry (Controller number 6, 38)

❍

Volume (Controller number 7)

• Volume messages are used to adjust the volume balance of each Part.

• Not received when Rx.VOLUME = OFF. (Initial value is ON)

❍

Pan (Controller number 10)

• The stereo position can be adjusted over 127 steps.

• For Rhythm Parts, this is a relative adjustment of each Instrument’s pan setting.

• Not received when Rx.PANPOT = OFF. (Initial value is ON)

❍

Expression (Controller number 11)

• This adjusts the volume of a Part. It can be used independently from Volume mes-

sages. Expression messages are used for musical expression within a performance;

e.g., expression pedal movements, crescendo and decrescendo.

• Not received when Rx.EXPRESSION = OFF. (Initial value is ON)

❍

Hold 1 (Controller number 64)

• Not received when Rx.HOLD1 = OFF. (Initial value is ON)

❍

Portamento (Controller number 65)

• Not received when Rx.PORTAMENTO = OFF. (Initial value is ON)

❍

Sostenuto (Controller number 66)

• Not received when Rx.SOSTENUTO = OFF. (Initial value is ON)

❍

Soft (Controller number 67)

• Not received when Rx.SOFT = OFF. (Initial value is ON)

❍

Filter Resonance (Timbre/Harmonic Intensity) (Controller number 71) [VA-3]

Status 2nd byte 3rd byte

8nH kkH vvH

9nH kkH 00H

n = MIDI channel number: 0H~FH (Ch.1~16)

kk = note number: 00H~7FH (0~127)

vv = note o velocity: 00H~7FH (0~127)

Status 2nd byte 3rd byte

9nH kkH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

kk = note number: 00H~7FH (0~127)

vv = note on velocity: 01H~7FH (1~127)

Status 2nd byte 3rd byte

AnH kkH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

kk = note number: 00H~7FH (0~127)

vv = key pressure: 00H~7FH (0~127)

Status 2nd byte 3rd byte

BnH 00H mmH

BnH 20H llH

n = MIDI channel number: 0H~FH (Ch.1~16)

mm = Bank number MSB: 00H~7FH (GS Variation number 0~127)

Initial value = 00H

ll = Bank number LSB: 00H~04H (MAP), Initial value = 00H

Status 2nd byte 3rd byte

BnH 01H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Modulation depth: 00H~7FH (0~127)

Status 2nd byte 3rd byte

BnH 05H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Portamento Time: 00H~7FH (0~127), Initial value = 00H (0)

Status 2nd byte 3rd byte

BnH 06H mmH

BnH 26H llH

n = MIDI channel number: 0H~FH (Ch.1~16)

mm, ll = the value of the parameter specied by RPN/NRPN

mm = MSB, ll = LSB

Status 2nd byte 3rd byte

BnH 07H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Volume: 00H~7FH (0~127), Initial value = 64H (100)

Status 2nd byte 3rd byte

BnH 0AH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = pan: 00H~40H~7FH (Left~Center~Right),

Initial value = 40H (Center)

Status 2nd byte 3rd byte

BnH 0BH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Expression: 00H~7FH (0~127), Initial value = 7FH (127)

Status 2nd byte 3rd byte

BnH 40H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Control value: 00H~7FH (0~127)

Status 2nd byte 3rd byte

BnH 41H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Control value: 00H~7FH (0~127) 0~63 = OFF, 64~127 = ON

Status 2nd byte 3rd byte

BnH 42H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Control value: 00H~7FH (0~127) 0~63 = OFF, 64~127 = ON

Status 2nd byte 3rd byte

BnH 43H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Control value: 00H~7FH (0~127) 0~63 = OFF, 64~127 = ON

Status 2nd byte 3rd byte

BnH 47H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv= Resonance value (relative

change):

00H~7FH (-64~0~+63),

Initial value = 40H (no change)

VA-3 MIDI Implementation

❍

Release Time (Controller number 72) [VA-3]

❍

Attack time (Controller number 73) [VA-3]

❍

Cutoff (Controller number 74) [VA-3]

❍

Decay Time (Controller number 75) [VA-3]

❍

Vibrato Rate (Controller number 76) [VA-3]

❍

Vibrato Depth (Controller number 77) [VA-3]

❍

Vibrato Delay (Controller number 78) [VA-3]

❍

Portamento control (Controller number 84)

• A Note-on received immediately after a Portamento Control message will change

continuously in pitch, starting from the pitch of the Source Note Number.

• If a voice is already sounding for a note number identical to the Source Note Number,

this voice will continue sounding (i.e., legato) and will, when the next Note-on is re-

ceived, smoothly change to the pitch of that Note-on.

• The rate of the pitch change caused by Portamento Control is determined by the Por-

tamento Time value.

Example 1.

Example 2.

❍

Eect 1 (Reverb Send Level) (Controller number 91)

• This message adjusts the Reverb Send Level of each Part.

❍

Eect 3 (Chorus Send Level) (Controller number 93)

• This message adjusts the Chorus Send Level of each Part.

❍

NRPN MSB/LSB (Controller number 99, 98)

n = MIDI channel number: 0H~FH (Ch.1~16)

mm = upper byte (MSB) of the parameter number specied by NRPN

ll = lower byte (LSB) of the parameter number specied by NRPN

• Rx.NRPN is set to OFF by power-on reset or by receiving “GM1 System On” or “GM2

System On,” and NRPN message will be ignored. NRPN message will be received

when Rx.NRPN= ON, or by receiving “GS RESET.”

• The value set by NRPN will not be reset even if Program Change or Reset All Con-

trollers is received.

**NRPN**

The NRPN (Non Registered Parameter Number) message allows an extended range

of control changes to be used. On the VA-3, NRPN messages can be used to modify

sound parameters, etc.

To use these messages, you must rst use NRPN messages (Controller number 98

and 99, their order does not matter) to specify the parameter to be controlled, and then

use Data Entry messages (Controller number 6) to specify the value of the specied

parameter. Once an NRPN parameter has been specied, all Data Entry messages

received on that channel will modify the value of that parameter. To prevent accidents,

it is recommended that you set RPN Null (RPN Number = 7FH 7FH) when you have

nished setting the value of the desired parameter. Refer to “5. Supplementary mate-

rial”, Examples of actual MIDI messages, [Example 4] (page 18). On the VA-3, Data

entry LSB (Controller number 38) of NRPN is ignored, so it is no problem to send Data

entry MSB (Controller number 6) only (without Data entry LSB).

On the VA-3, NRPN can be used to modify the following parameters.

Status 2nd byte 3rd byte

BnH 48H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv= Release Time value (relative

change):

00H~7FH (-64~0~+63),

Initial value = 40H (no change)

Status 2nd byte 3rd byte

BnH 49H vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv= Attack time value (relative

change):

00H~7FH (-64~0~+63),

Initial value = 40H (no change)

Status 2nd byte 3rd byte

BnH 4AH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv= Cuto value (relative change): 00H~7FH (-64~0~+63),

Initial value = 40H (no change)

Status 2nd byte 3rd byte

BnH 4BH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv= Decay Time value (relative

change):

00H~7FH (-64~0~+63),

Initial value = 40H (no change)

Status 2nd byte 3rd byte

BnH 4CH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv= Vibrato Rate value (relative

change):

00H~7FH (-64~0~+63),

Initial value = 40H (no change)

Status 2nd byte 3rd byte

BnH 4DH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv= Vibrato Depth value (relative

change):

00H~7FH (-64~0~+63),

Initial value = 40H (no change)

Status 2nd byte 3rd byte

BnH 4EH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv= Vibrato Delay value (relative

change):

00H~7FH (-64~0~+63),

Initial value = 40H (no change)

Status 2nd byte 3rd byte

BnH 54H kkH

n = MIDI channel number: 0H~FH (Ch.1~16)

kk = source note number: 00H~7FH (0~127)

On MIDI Description Result

90 3C 40 Note on C4 C4 on

B0 54 3C Portamento Control from C4 no change

90 40 40 Note on E4 glide from C4 to E4

80 3C 40 Note o C4 no change

80 40 40 Note o E4 E4 o

On MIDI Description Result

B0 54 3C Portamento Control from C4 no change

90 40 40 Note on E4 E4 is played with a glide from C4 to E4

80 40 40 Note o E4 E4 o

Status 2nd byte 3rd byte

BnH 5BH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Reverb Send Level: 00H~7FH (0~127), Initial value = 28H (40)

Status 2nd byte 3rd byte

BnH 5DH vvH

n = MIDI channel number: 0H~FH (Ch.1~16)

vv = Chorus Send Level: 00H~7FH (0~127), Initial value = 00H (0)

Status 2nd byte 3rd byte

BnH 63H mmH

BnH 62H llH

NRPN

MSB LSB

Data entry

MSB Function and range

01H 08H mmH Vibrato Rate (relative change)

mm: 00H~40H~7FH (-64~0~+63)

01H 09H mmH Vibrato Depth (relative change)

mm: 00H~40H~7FH (-64~0~+63)

01H 0AH mmH Vibrato Delay (relative change)

mm: 00H~40H~7FH (-64~0~+63)

01H 20H mmH TVF Cuto Frequency (relative change)

mm: 00H~40H~7FH (-64~0~+63)

01H 21H mmH TVF Resonance (relative change)

mm: 00H~40H~7FH (-64~0~+63)

01H 63H mmH TVF&TVA Envelope Attack Time (relative change)

mm: 00H~40H~7FH (-64~0~+63)

01H 64H mmH TVF&TVA Envelope Decay Time (relative change)

mm: 00H~40H~7FH (-64~0~+63)

01H 66H mmH TVF&TVA Envelope Release Time (relative change)

mm: 00H~40H~7FH (-64~0~+63)

18H rrH mmH Drum Instrument Pitch Coarse (relative change)

rr: Drum Instrument note number

mm: 00H~40H~7FH (-64~0~+63 semitone)

1AH rrH mmH Drum Instrument TVA Level (absolute change)

rr: Drum Instrument note number

mm: 00H~7FH (0~max)

1CH rrH mmH Drum Instrument Panpot (absolute change)

rr: Drum Instrument note number

mm: 00H, 01H~40H~7FH (random, left~center~right)

1DH rrH mmH Drum Instrument Reverb Send Level (absolute change)

rr: Drum Instrument note number

mm: 00H~7FH (0~max)

1EH rrH mmH Drum Instrument Chorus Send Level (absolute change)

rr: Drum Instrument note number

mm: 00H~7FH (0~max)

4FH 10H mmH Part 4 On / O (Upper 1) [VA-3]

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 11H mmH Part 11 On / O (Lower1)

mm: 00H~ 7FH (00-3FH =O~40-7FH= On)

4FH 12H mmH Part 12 On / O (Man Bass)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 13H mmH Part 6 On / O (Upper 2)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 14H mmH Part 16 On / O (Man Drums)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 27H mmH Part 14 On / O (Lower 2)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 26H mmH Part 15 On / O (Melody Int.)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 18H mmH Part 8 On / O (Acc 5)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 19H mmH Part 9 On / O (Acc 6)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 1AH mmH Part 10 On / O (Acc Drums)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

4FH 1BH mmH Part 2 On / O (Acc Bass)

mm: 00H~7FH (00-3FH =O~40-7FH= On)

Produkt Specifikationer

Mærke:	Roland
Kategori:	Ikke kategoriseret
Model:	VA-3

Har du brug for hjælp?

Hvis du har brug for hjælp til Roland VA-3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Roland Manualer

Roland ATUP-EX Manual

9 Juni 2025

Roland PD-10X Manual

1 Juni 2025

Roland VH-11 Manual

31 Maj 2025

Roland PD-12X Manual

31 Maj 2025

Roland GO:KEYS 3 IN Manual

20 Marts 2025

Roland FD-7 Manual

28 Februar 2025

Roland Space Echo RE-201 Manual

27 Februar 2025

Roland VR-3EX Manual

26 Februar 2025

Roland KSFE50 Manual

20 Februar 2025

Roland KS-V7 Manual

30 December 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet Audio P100CPA Manual

15 Juni 2025

Sabrent BK-MAC2 Manual

15 Juni 2025

Planet Audio P9950CPA Manual

15 Juni 2025

Filmcity FC-CTH-01 Manual

15 Juni 2025

Cleveland 22CGT6 Manual

15 Juni 2025

Auray SVRK-4U-S Manual

15 Juni 2025

Bobrick B-2860 Manual

15 Juni 2025

Sony ODBK-103 Manual

15 Juni 2025

Planet Audio P70CPA Manual

15 Juni 2025

Gourmia GAF657 Manual

15 Juni 2025