Roland XI-MADI Manual

Roland Ikke kategoriseret XI-MADI

Læs gratis den danske manual til Roland XI-MADI (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Roland XI-MADI, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES”

on back side. After reading, keep the document(s) including those sections where it will be

available for immediate reference.

* 5100044931- 01*

Installing the Expansion interface

Install the expansion interface on a compatible device.

Important Notes on Handling

To avoid the risk of damage to internal components that can be caused by static electricity,

please carefully observe the following whenever you handle the expansion interface.

• Before you touch the expansion interface, always rst grasp a metal object (such as a

water pipe), so you are sure that any static electricity you might have been carrying

has been discharged.

• When handling the expansion interface, grasp it only by the panel or the expansion

interface’s edges. Avoid touching any of the electronic components or connectors.

• Before you connect any cables, make sure they do not carry a static electricity charge.

Such charges can be transmitted, for example, if the other end of the cable has been

in contact with a carpet (or other object) where there is a static electricity buildup.

• Save the bag in which the expansion interface was originally shipped, and put the

expansion interface back into it whenever you need to store or transport it.

Installing

NOTE

• Before installing the expansion interface, you must rst always turn o the unit where

installing and unplug its power cord from the power outlet.

• When restarting the device with the expansion interface installed, wait several

seconds before turning on the power.

1. Loosen the EXPANSION SLOT mounting screws (2) on the device where you’re

installing, and detach the panel cover.

2. Insert the expansion interface into the EXPANSION SLOT.

* Do not touch any of the expansion interface pathways or connection terminals.

* Never use excessive force when installing a expansion interface. If it doesn’t t properly

on the rst attempt, remove the expansion interface

and try again.

3. Secure the expansion interface in place using the mounting screws (2).

Panel Descriptions

1 2

No. Name Explanation

1 VIDEO SYNC IN

connector

This is for input of a black-burst signal.

Here you connect a black-burst generator or other such external

source device when synchronizing the XI-MADI-compatible device

to video equipment.

2 MADI IN/OUT

connectors 1, 2

(optical)

These are optical-type connectors for MADI input and output.

* When no cable is used, attach the connector cap to prevent

entry by dust or other foreign matter. The unit is shipped from

the factory with the connector caps attached to the connectors.

About optical cables

• Use multi-mode ber-optic cable having a core diameter or

50/125 μm or 62.5/125 μm.

• Cable length can be up to 2,000 meters per cable.

• Use SC connectors compliant with ISO/IEC 9314-3.

3 MADI IN/OUT

connectors 1, 2

(coaxial)

These are BNC-type connectors for MADI input and output.

About coaxial cables

• Use cables whose impedance is 75 Ω.

• Cable length can be up to 100 meters per cable.

• Use BNC-type connectors compliant with IEC 60169-8.

• Canare L-5C2VS cable or equivalent is recommended.

Main Features

MADI (Multichannel Audio Digital Interface) is a transmission standard for digital audio

standardized by AES. An extension of the AES/EBU standard for stereo (two-channel)

transmission, it permits transmission of up to 64 channels over a single cable.

The main features of the XI-MADI are as follows.

• Equipped with two types of MADI connectors: optical and BNC

Optical and BNC (coaxial) MADI connectors are provided. You can select separate

connectors for both MADI 1 and MADI 2.

* When signals on the same channel are input via both the optical connector and the

BNC connector, the BNC input takes priority.

* Once optical input has been selected, the system does not switch to BNC as long as

an optical signal continues to be input.

* Depending on the equipment in which the XI-MADI is installed, locking input to

optical or BNC might be possible.

• Support for redundant main and backup transmission

Using a MADI 1 connector as main and a MADI 2 connector as backup is possible. In the

event of a problem with the main connection, the system automatically switches to the

backup connection.

* Redundant transmission uses either all-optical or all-BNC connections. Redundant

transmission combining optical with BNC is not supported.

• Equipped with a VIDEO SYNC IN connector

A VIDEO SYNC IN connector allowing black-burst signal input is provided. Selecting

the VIDEO SYNC IN connector as the clock source enables synchronization with video

equipment.

* For information on the equipment in which the XI-MADI can be installed, check the

following Roland website.

http://proav.roland.com

Thank you, and congratulations on your choice of the XI-MADI expansion

interface.

Installing this expansion interface card in professional audio equipment

from Roland makes it possible to expand audio input and output using

MADI (Multichannel Audio Digital Interface).

For information on devices on which the XI-MADI expansion interface

can be installed, check the Roland website.

http://proav.roland.com

Setup Guide

Main Specications

Channels Up to 64 channels input/output x 2 (48 kHz, 44.1 kHz, 64 ch mode)

Up to 32 channels input/output x 2 (96 kHz, 64 ch mode)

* The number of available channels will be changed by the device that

attach the XI-MADI.

Signal

Processing

Sampling Frequency 96 kHz, 48 kHz, 44.1 kHz

MADI channel mode 64 ch, 56 ch

Data Length 24 bits

Connectors Coaxial MADI IN (1, 2) connectors BNC type

Coaxial MADI OUT (1, 2) connectors BNC type

Optical MADI IN/OUT (1, 2)connectors SC duplex multi mode type (*1)

VIDEO SYNC IN connector BNC type

USB COMPUTER port

(Inside of the panel, updates only)

USB type B

Power

Consumption 7.0 W

Dimensions 120 (W) x 185 (D) x 40 (H) mm

4-3/4 (W) x 7-5/16 (D) x 1-5/8 (H) inches

* Protruding parts not included.

Weight 250 g

9 oz

Operation

Temperature

+5 to +40 degrees Celsius

+41 to +104 degrees Fahrenheit

Accessories Setup Guide, Ferrite core x 5

(*1): For single mode type, consult your Roland vendor.

* In the interest of product improvement, the specications and/or appearance of this unit

are subject to change without prior notice.

Attaching Ferrite Cores

Attach ferrite cores to cables connected to the MADI IN/OUT connectors (coaxial) or VIDEO

SYNC IN connector.

* The ferrite cores are needed to prevent electromagnetic noise. Be sure to attach ferrite

cores to any cables connected to the MADI IN/OUT connectors (coaxial) or the VIDEO

SYNC IN connector.

1. Open an included ferrite core by spreading apart the tabs at two places.

2. Attach the ferrite core at a location near the plug base.

Close the ferrite core by pressing down on each tab until it clicks into place.

MEMO

Connect the plug at the end where the ferrite core is attached to the connector on the

other device.

Produkt Specifikationer

Mærke:	Roland
Kategori:	Ikke kategoriseret
Model:	XI-MADI
Bredde:	120 mm
Dybde:	185 mm
Højde:	40 mm
Vægt:	250 g
Produktfarve:	Sort
Strømforbrug (typisk):	7 W
Driftstemperatur (T-T):	5 - 40 °C
Antal:	1
Hurtig installationsvejledning:	Ja
Intern:	Ja
Kapabilitet:	Roland M-5000
Output-grænseflade:	BNC