Sanyo LNS-T33 Manual


Læs gratis den danske manual til Sanyo LNS-T33 (8 sider) i kategorien Tilbehør til projektor. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Sanyo LNS-T33, eller vil du spørge andre brugere om produktet?

Side 1/8
Following checks and confirmations should be taken for safety.
Check the following things by the time of the cabinet mount after the lens replacement.
1. Check the lens is securely fixed.
2. Check the proper wiring and the wires are fixed properly.
3. Check each connector is connected properly.
4. Check no wiring is tangled on the gear of lens motor or the other mechanical parts.
5. Check no parts is missing, or no mounting part is loose.
LCD PROJECTOR LENS
MODEL LNS-T33
LENS REPLACEMENT PROCEDURE
Lens replacement should be performed by the qualified service personnel.
It should be followed by this procedure precisely.
Before attempt to replace the lens, confirm the model number (both the
LCD projector and the lens) and use the proper lens.
The lens cover is on the lens for protection. Be sure to remove the lens
cover before installation.
When installing or removing the lens, be careful not to stain, scratch or
damage the lens.
When shipping the projector with the lens, remove the lens before shipping
the projector.
If you have any questions, contact the dealers.
Following parts are contained in the packing.
1AA6P1P5722-- (IFRD)
PARTS LIST
LENS
SCREW DRIVER (3 mm, Green)
SCREW DRIVER (4 mm, Yellow)
LIGHT-BLOCK SHEET
SPACER
CABLE TIE
1 piece
1 piece (Part No. 910 287 7329)
1 piece (Part No. 910 275 6020)
1 piece Type PJ1 (Part No. 610 347 3901)
1set (Part No. 610 301 6658)
2 pieces (Part No. 645 004 5387)
NOTE; Lens installation is different in cabinet design (Type A and B). Before installation
the lens, check cabinet design.
Some parts are not used for installation or replacement. Keep these parts and
drivers included in the lens for later use.
Printed in Japan
Notes on Lens Replacement
Turn the lens cover to counter-clockwise and pull it
toward front and remove the lens cover.
Remove 2 screws-A.
Remove the front cabinet
R EMOVE THE LEN S C OV ER AN D
FRONT CABINET
1
1.
2.
2REMOVE THE LIGHT-BLOCK SHEET BASE
AND LIGHT-BLOCK SHEET
Perform the steps to for lens replacement.
16
At first set the lens at the fully lower position with lens
shift adjustment.
3.
Slide the light-block sheet base upward and
remove it.
Remove the light-block sheet from lens.
1.
2.
LIGHT-BLOCK
SHEET BASE
FRONT
CABINET
LENS COVER
LIGHT-BLOCK
SHEET
SCREW "A"
LENS COVER
FRONT CABINET
LENS REPLACEMENT PROCEDURE (FOR "A" TYPE )
SCREW "A"
FRONT CABINET
LIGHT-BLOCK
SHEET BASE
LIGHT-BLOCK
SHEET
FRONT
CABINET
- 2 -
Remove 2 screws-A.
Remove the front cabinet
1.
2.


Produkt Specifikationer

Mærke: Sanyo
Kategori: Tilbehør til projektor
Model: LNS-T33
Brændviddeområde: 148 - 234 mm
Blændeområde (F-F): 2.2 - 2.7
Throw-forhold: 5.7 - 9.0:1
Zoomforhold: 1.56x

Har du brug for hjælp?

Hvis du har brug for hjælp til Sanyo LNS-T33 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Tilbehør til projektor Sanyo Manualer

Sanyo

Sanyo POA-FIL131 Manual

1 September 2023
Sanyo

Sanyo LNS-S04 Manual

22 Juli 2023
Sanyo

Sanyo LNS-T02E Manual

2 November 2022
Sanyo

Sanyo LNS-T33 Manual

13 Oktober 2022

Tilbehør til projektor Manualer

Nyeste Tilbehør til projektor Manualer