Schneider MTN644792 Manual

Schneider Ikke kategoriseret MTN644792

Læs gratis den danske manual til Schneider MTN644792 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Schneider MTN644792, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The binary input REG-K/8x24 is used to connect eight

conventional 24 V devices (e.g. door and window

contacts) to the bus system.

The binary input has a bus coupler. It is installed on a

DIN rail acc. to EN 60715, with the bus connection

made via a bus connecting terminal. A data rail is not

required.

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• The internal device connection of the potentials is not

suitable for carrying load currents.

• Only operate the device according to the specifica-

tions stated in the Technical data.

• All the devices that are installed next to the binary in-

put must be equipped with basic insulation at the very

least.

Failure to follow these instruction can result in

equipment damage.

Binary input introduction

ACover of the bus connecting terminal

BProgramming button/programming LED

COperational LED

DChannel status LEDs

1Set the binary input onto the DIN rail.

2Connect KNX.

WARNING

Risk of fatal injury from electrical current.

The device could be damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

½CAUTION

The device could be damaged.

High voltages can cause damage. Never connect

devices with more than 24 V.

Operating and display elements

Installing the binary input

RUNE 8E 7

E 6E 5E 4E 3E 2E 1

E1 0 V 0 V E2 E3 0 V 0 V E4

E5 0 V 0 V E6 E7 0 V 0 V E8

5 mm

1 2

3 4

230 V

4 mm

KNX

3Connect the input cables.

|The 0 V conductors must be connected to the

device. Inputs E1 to E4 have a common potential

(4 x 0 V, top row) and inputs E5 to E8 have a

common potential (4 x 0 V, bottom row).

1Press the programming button.

The programming LED lights up.

2Load the physical address and the application into

the device from the ETS.

The operating LED lights up: The application was loaded

successfully, the device is ready for operation.

Schneider Electric Industries SAS

35 rue Joseph Monier

Rueil Malmaison 92500

France

If you have technical questions, please contact the Cus-

tomer Care Centre in your country.

se.com/contact

Putting the binary input into operation

Technical data

Power supply from

bus: DC 24 V / max.18 mA

Insulation voltage: AC 4 kV bus/inputs

Inputs

Nominal voltage: AC/DC 24 V

0 signal: < 5 V

1 signal: > 11 V

Nominal current: DC approx. 15 mA (30 V),

AC approx. 6 mA (27 V)

Permitted cable

length: max. 100 m/channel

Ambient temperature

Operation: -5 °C to +45 °C

Storage: -25 °C to +55 °C

Transport: -25 °C to +70 °C

Max. humidity: 93 % relative humidity, no

moisture condensation

Environment: The device is designed for use

at a height of up to 2000 m

above sea level (MSL).

Connections

Inputs, outputs: Screw terminals

Single-core: 1.5 mm2 to 2.5 mm2

Finely stranded

(with core end sleeve): 1.5 mm2 to 2.5 mm2

Bus: Bus connecting terminal

Dimensions

Height x width x

depth: 90 x 72 x 65 mm

Device width: 4 modules

Schneider Electric -Contact

KNX

+ -

24V 0V

Schneider Electric Limited

Telford, TF3 3 BL, UK

UK Representative

Stafford Park 5

SpaceLogic KNX Binary input REG-K/8x24

Operating instructions

Art. no. MTN644792

RUNE 8E 7E 6E 5E 4E 3E 2E 1

V6447-562-01 11/21

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN644792

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN644792 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider IAP05S Manual

9 Juli 2025

Schneider PowerLogic HDPM6000 Manual

7 Juli 2025

Schneider GS1DDB4 Manual

6 Juli 2025

Schneider LUCAX6ES Manual

4 Juli 2025

Schneider DF14AM2 Manual

4 Juli 2025

Schneider LUCD1XES Manual

4 Juli 2025

Schneider KSB32CP15D Manual

4 Juli 2025

Schneider LUCB32ES Manual

4 Juli 2025

Schneider LUCB12ES Manual

3 Juli 2025

Schneider NSYPLAT1273G Manual

3 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025