Schneider MTN644992 Manual

Schneider Ikke kategoriseret MTN644992

Læs gratis den danske manual til Schneider MTN644992 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Schneider MTN644992, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The binary input REG-K/4x230 is used to connect four

conventional 230 V devices (such as movement

detectors and light-sensitive switches) to the KNX bus.

The binary input has a bus coupler. It is installed on a

DIN rail acc. to EN 60715, with the bus connection

made via a bus connecting terminal. A data rail is not

required.

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• The internal device connection of the potentials is not

suitable for carrying load currents.

• Only operate the device according to the specifica-

tions stated in the Technical data.

• All the devices that are installed next to the binary in-

put must be equipped with basic insulation at the very

least.

Failure to follow these instruction can result in

equipment damage.

Binary input introduction

A Cover of the bus connecting terminal

B Programming button and programming LED (behind

hinged cover)

C Operational LED

D Channel status LEDs

1 Set the binary input onto the DIN rail.

2 Connect KNX.

WARNING

Risk of fatal injury from electrical current.

The device could be damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

½CAUTION

The device could be damaged.

High voltages can cause damage. Never connect

devices with more than 230 V.

Operating and display elements

Installing the binary input

E1 N E2 E3 N E4

E 4E 2

RUNE 1 E 3

1 2

5 mm

230 V

4 mm

KNX

3 Connect the input cables.

When the bus voltage is connected and there is a signal

at the input, the corresponding yellow channel status

LED will light up.

|The N conductors must be connected to the

device. Inputs E1 to E4 have a common potential

(4 x N). Inputs E1 to E4 can be assigned to each

other with different phases.

1 Press the programming button.

The programming LED lights up.

2 Load the physical address and the application into

the device from the ETS.

The operating LED lights up: The application was loaded

successfully, the device is ready for operation.

Schneider Electric Industries SAS

35 rue Joseph Monier

Rueil Malmaison 92500

France

If you have technical questions, please contact the Cus-

tomer Care Centre in your country.

se.com/contact

Putting the binary input into operation

Technical data

Supply from KNX: DC 24 V / max.18 mA

Insulation voltage: AC 4 kV bus/inputs

Inputs

Nominal voltage: AC 230 V ±10 %, 50/60 Hz

0 signal: < 40 V

1 signal: > 160 V

Nominal current: AC approx. 7 mA

Permitted cable

length: max. 100 m/channel

Ambient temperature

Operation: -5 °C to +45 °C

Storage: -25 °C to +55 °C

Transport: -25 °C to +70 °C

Max. humidity: 93 % relative humidity, no

moisture condensation

Environment: The device is designed for use

at a height of up to 2000 m

above sea level (MSL).

Connections

Inputs, outputs: Screw terminals

Single-core: 1.5 mm2 to 2.5 mm2

Finely stranded

(with core end sleeve): 1.5 mm2 to 2.5 mm2

KNX: Bus connecting terminal

Dimensions

Height x width x

depth: 90 x 45 x 65 mm

Device width: 2.5 modules

Schneider Electric -Contact

KNX

+ - L1 L2 L3 N

Schneider Electric Limited

Telford, TF3 3 BL, UK

UK Representative

Stafford Park 5

SpaceLogic KNXBinary input REG-K/4x230

Operating instructions

Art. no. MTN644992

E 4E 2

RUNE 1 E 3

V6449-562-01 11/21

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN644992

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN644992 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider Homeline HOM250PSPD Manual

4 November 2025

Schneider BC650-RSX761 Manual

7 Oktober 2025

Schneider P8VNTG Manual

1 Oktober 2025

Schneider QCGK3 Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3319 Manual

1 Oktober 2025

Schneider Altivar 312 VZ3V3103 Manual

1 Oktober 2025

Schneider SCTK30 Manual

1 Oktober 2025

Schneider Altivar 71 VW3A7201 Manual

1 Oktober 2025

Schneider OHBS Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3502 Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navitel ALC 01 Manual

5 November 2025

SilentiumPC Vero L3 Bronze 600W Manual

5 November 2025

JoeCo BlackBox BBR1-U Manual

5 November 2025

Ices IWO-630 Manual

5 November 2025

JMAZ Crazy Beam 40 Fusion Manual

5 November 2025

Lexar Professional LRW530U Manual

5 November 2025

Zotac GeForce GT 610 Manual

5 November 2025

NeXtime Basic Dome 3157 ZW Manual

5 November 2025

DS18 PU110A Manual

5 November 2025

JMAZ Galaxy Tube Manual

5 November 2025