Schneider MTN6600-0603 Manual

Schneider Ikke kategoriseret MTN6600-0603

Læs gratis den danske manual til Schneider MTN6600-0603 (15 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Schneider MTN6600-0603, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/15
© 2012 Schneider Electric 1
Energy Meter REG-K/3x230/16 A
Art no. MTN6600-0603
Application Energy metering/saving/calculating 7601/1.0
Table of contents
Function overview
Using this application, you can operate the REG-K/
3x230/16 A energy counter for measuring and monitor-
ing energy. This means you can monitor up to 3 chan-
nels independently of one another. You can send the
data to the KNX bus for evaluation.
You have access both to channel-dependent and chan-
nel-independent functions.
When the application is loaded, the following functions
can be implemented, evaluated and controlled via the
bus:
You can set a separate energy saving and alarm func-
tion with corresponding actions for each channel:
Application Energy metering/saving/cal-
culating 7601/1.0
• Function overview 1
• Behaviour of the application 2
• General functions 2
– Select channels (1-3) 2
– Nominal voltage level 3
– Start delay 3
• Functions per channel 3
– Energy counter 3
– Energy saving function 4
– Alarm function 6
• Data transmission 7
• Tariff counter 8
• Energy calculator 9
• Status 10
– Bus voltage failure counter 10
– Energy counter and total energy counter 10
– Tariff counter 11
• Overview of parameters 12
• Overview of communication objects 15
Channel 1
Channel 2
Channel 3
Energy counter
Energy saving function
Alarm function
Data transmission
Tariff counter
Energy calculator
Status
Energy counter
Energy saving function
Alarm function
Energy counter
Energy saving function
Alarm function
Channel 1-3
Energy saving function Threshold 1-8
Switch object
Dimming object
Value object
Scene object
Temperature object
Alarm function Alarm limits
Alarm object
Alarm object
2© 2012 Schneider Electric
Energy Meter REG-K/3x230/16 A
Art no. MTN6600-0603
Behaviour of the application
|Many parameters and their settings are depend-
ent on the settings you have already made for oth-
er parameters. This means that some parameters
will appear or disappear and the values available
for selection will change according to settings you
have already made. These dependencies have
not been shown in the table for reasons of clarity.
All settings are always shown.
|Configurable times are set via the base and factor
parameters. The actual time is given by the multi-
plication of the two values. Example:
Base = 1 second, Factor = 3
Actual time = 3 seconds
|The bold values in a table are the values set dur-
ing factory configuration.
The application is influenced by the following events:
• ETS download
• Bus voltage failure
• Bus voltage recovery
The behaviour differs according to function and can in-
fluence the measuring and monitoring function. There-
fore, you can set the behaviour using parameters at the
corresponding point. Refer to the chapter in question
for a precise description.
Select channels
You can enable channels 1-3 separately. On enabled
channels, you can then set additional functions (energy
saving and alarm function) using parameters.
Parameters
Data transmission
You can send the measured current and power values
per channel for evaluation and visualisation to the KNX
bus.
Further settings are possible using parameters on an
enabled function.
Parameters
Tariff counter
You can count the energy separately for up to four tar-
iffs. Using these values, you can then calculate your en-
ergy costs according to the applicable tariff.
Further settings are possible using parameters on an
enabled function.
Parameters
Energy calculator
You can add together the measured current and power
values of several channels and send them for evalua-
tion and visualisation to the KNX bus.
Further settings are possible using parameters on an
enabled function.
Parameters
Behaviour of the application
General functions
General functions
Parameters Setting
Channel X Disabled
Enabled
General functions
Parameters Setting
Data transmission Disabled
Enabled
General functions
Parameters Setting
Tariff counter Disabled
Enabled
General functions
Parameters Setting
Energy calculator Disabled
Enabled

Produkt Specifikationer

Mærke: Schneider
Kategori: Ikke kategoriseret
Model: MTN6600-0603

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN6600-0603 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Schneider Manualer

Schneider

Schneider SSM1A16P7 Manual

1 April 2025
Schneider

Schneider VB310R Manual

1 April 2025
Schneider

Schneider GV2APN04 Manual

1 Januar 2025
Schneider

Schneider LU9APN21 Manual

1 Januar 2025
Schneider

Schneider RE22R1MAMR Manual

12 December 2024
Schneider

Schneider LXMMC12MS06S100 Manual

6 December 2024
Schneider

Schneider LXMMC12MA02S100 Manual

6 December 2024
Schneider

Schneider MTN647595 Manual

20 September 2024
Schneider

Schneider CCT15910 Manual

12 September 2024
Schneider

Schneider Wiser CCT593012 Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tracer

Tracer Ambience - Smart Circle Manual

17 Juni 2025
Ulsonix

Ulsonix ULX-480-1 Manual

17 Juni 2025
JUNG

JUNG CD 104.18 WU Manual

17 Juni 2025
Hughes & Kettner

Hughes & Kettner TriAmp MKII Manual

17 Juni 2025
Cecotec

Cecotec Bean&Clean Manual

17 Juni 2025
Steinberg

Steinberg SBS-FZ 3000/3BM Manual

17 Juni 2025
Mars Gaming

Mars Gaming MPB1000SI Manual

17 Juni 2025
Stamos

Stamos SWS05 Manual

17 Juni 2025
Royal Catering

Royal Catering RCAT-140/80 Manual

17 Juni 2025
Planet Audio

Planet Audio P90CPAP Manual

17 Juni 2025