Schneider MTN6725-0003 Manual

Schneider Ikke kategoriseret MTN6725-0003

Læs gratis den danske manual til Schneider MTN6725-0003 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Schneider MTN6725-0003, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

V6725-563-02 11/21

SpaceLogic KNX DALI Gateway Basic

REG-K/1/16/64

Operating instructions

Art. no. MTN6725-0003

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connection and setup of KNX networks

• Connection and setup of DALI networks

• Connection and setup of emergency lighting sys-

tems

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

KNX / PRGD1+ D1-

L N PE

1/9 2/10 3/11 4/12

5/13 6/14 7/15 8/16 Man.

The KNX DALI Gateway Basic REG-K/1/16/64 (referred

to below as the gateway) connects the KNX bus to the

DALI bus. Lights with DALI electronic ballasts can there-

fore be integrated into a complete KNX system in the

form of a subsystem and operated using the wide range

of KNX devices available.

The device converts switching and dimming commands

of the connected KNX system into corresponding DALI

telegrams or status information from the DALI bus into

KNX telegrams.

The electronic ballasts can be switched, dimmed or set

to a defined value in 16 groups for each gateway.

|Notes

• Single Master Application Controller (EN

62386-103). The device may only be operated

in DALI lines with electronic ballasts connected

and not with other DALI control units within the

line (no multi-master operation).

• The power required for up to 64 connected

electronic ballasts is supplied directly from the

gateway. No additional DALI power supply is

required, nor is this permissible.

• The special interface for configuration of the

DALI segment is designed as a DCA (Device

Control App) for the ETS5.

Note that, in addition to the product database

(knxprod file), a corresponding ETS app (et-

sapp file) is also installed. Both files are availa-

ble in the KNX online catalogue and on the

manufacturer website.

• DALI devices for single-battery emergency

lights of device type DT-1 can be read by the

gateway and switched and operated via DALI

telegrams if required. DALI commands for

starting and reading test results are not sup-

ported.

Product features

• Addressing of 16 DALI groups

• Flexible DALI commissioning concept in ETS5

• Coloured light control with the support of ballasts of

device type 8

• Coloured light control depending on ballast subtype:

– Colour temperature (DT-8 subtype Tc)

– XY colour (DT-8 subtype XY)

– RGB (DT-8 subtype RGBWAF)

– HSV (DT-8 subtype RGBWAF)

– RGBW (DT-8 subtype RGBWAF)

– DT-8 subtype PrimaryN is not supported

• Support of timer programmes for control of groups by

value and/or colour

• Various operating modes for groups such as continu-

ous operation, night mode, staircase mode

• Integrated operating hours counter for each group,

with alarm once the end of the service life has been

reached

• Individual fault detection with objects for each individ-

ual light/electronic ballast

• Complex evaluation of faults at group/device level with

fault number and fault rate calculation

• Fault threshold monitoring with individually adjustable

threshold values

• Scene module for comprehensive programming of

scenes

• Quick exchange function for simple replacement of in-

dividual defective electronic ballasts

• Manual operation of group and broadcast telegrams

via operating buttons on the device

• Signalling of fault states and statuses via LEDs on the

device

Getting to know the Gateway Starting up the gateway

Several steps are necessary to start up the gateway fully:

1 Wire the DALI segment

2 Connect the gateway to DALI and KNX bus

3 Connect the gateway to the mains voltage

4 Load the ETS application programme (.knxprod)

and install the ETS app (.etsapp)

5 Configure the ETS parameters and objects

6 Assign the ETS-DCA DALI groups

7 Start up the ETS-DCA DALI

8 ETS download of application

|For a precise description of the start-up proce-

dure, read these operating instructions and the

latest application description.

It is installed on a TH35 DIN rail acc. to EN 60715, with

the bus connection made via a bus connecting terminal.

Network and DALI cables are connected via screw termi-

nals on the device.

The appliance connections as well as the programming

button and programming LEDs required for KNX com-

missioning can only be accessed in the distribution

board when the cover is removed.

Manual mode buttons can be operated and indicator

LEDs read with the distributor cover closed.

A KNX bus connecting terminal

B Programming button, normal/programming mode

C Programming LED, normal/programming mode

D DALI output terminal

E Operating buttons with a status LED (red) for each

group (1-8 and 9-16) for manual mode (group oper-

ation/group status, broadcast and service func-

tions)

F Mains connection

G Operating button with status LED (RGB) for activat-

ing manual mode

|Further information on operation, operating

modes and troubleshooting can be found in the

application description.

Connections, displays and operating

elements

KNX / PRGD1+ D1-

L N PE

1/9 2/10 3/11 4/12

5/13 6/14 7/15 8/16 Man.

ACD

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN6725-0003

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN6725-0003 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider BC650-RSX761 Manual

7 Oktober 2025

Schneider P8VNTG Manual

1 Oktober 2025

Schneider QCGK3 Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3319 Manual

1 Oktober 2025

Schneider Altivar 312 VZ3V3103 Manual

1 Oktober 2025

Schneider SCTK30 Manual

1 Oktober 2025

Schneider Altivar 71 VW3A7201 Manual

1 Oktober 2025

Schneider OHBS Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3502 Manual

1 Oktober 2025

Schneider Altivar 21 VW3A21101 Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ANCEL BM200 PRO Manual

3 November 2025

Ikea SPRETGRÄS 805.895.76 Manual

3 November 2025

ANCEL BM200 Manual

3 November 2025

JSAUX SP0210 Manual

3 November 2025

EtherWAN SmartE Manual

3 November 2025

Hikvision DS-TMG022 Manual

3 November 2025

Hendi 229583 Manual

3 November 2025

Witt HP 18 Manual

3 November 2025

Physa PHY-WU_03 Manual

3 November 2025

Beverage-Air Cross Temp CT2HC-1G Manual

3 November 2025