Sescom SES-X Manual


Læs gratis den danske manual til Sescom SES-X (4 sider) i kategorien Audio/video konverter. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Sescom SES-X, eller vil du spørge andre brugere om produktet?

Side 1/4
SES-X-FA2 2-Channel Mic & Line Level Audio over Fiber Extender
AC Adapters or Battery Operated
FEATURES
 2-Channel Directional, Analog Audio to Fiber Transmission
 24-Bit Digitally Encoded Analog Audio, 48KHz Sample Rate
 Supports Multimode Fiber up to 984 feet
 Supports Single Mode Fiber up to 12.4 miles
 Switchable Balanced Mic or Line Level Inputs
 Wide Dynamic Optical Range Requires No Optical Adjustments
 Power: AC Adapter or Standard 9VDC Battery
 Battery Runtime: Alkaline - Approximately 4 hours
 1 Year Warranty
 FCC & RoHS Compliant
Set Up Instructions
1. Secure the units in a safe location, where they will not be subject to impact and where there is room around the
unit so nothing will interfere with the fiber optic cabling causing it to bend sharply in a tight radius in any way that
can severely affect the signal transfer.
2. Use proper cable management and handling for routing fiber optic cable.
3. Carefully connect your source(s) to the transmitter input(s) and the receiver unit output(s) to your receiving device
input(s) using the XLR connectors on the transmitter and on the receiver unit.
4. Note that audio on the transmitter (Tx) can be Line or Mic level input and the receiver (Rx) is Line level only.
5. CLEAN* the ST fiber optical cable contacts that will be used for connecting the Tx and Rx units and attach the fiber
cable to the ST connections and secure, as you would secure a bayonet BNC. While pressing lightly in on the
connector, twist it in a clockwise direction about 1/8 to 1/4 of a turn and then release. The connector should stay
inserted and have backwards spring pressure holding the bayonet in place.
6. Connect the included power supplies to the transmitter and receiver units, and plug them both into an AC power
source (100-240VAC 50/60Hz) or insert the 9V batteries in both units for remote use.
* CLEAN: All fiber optical cable contacts require cleaning each time before inserting into a device’s outputs or
inputs. Failure to clean the contacts can damage the unit’s optics over time and can also permanently damage
the cable and the device.
Use cleaning kits designed specifically for fiber optics.
SES-X-FA2 AUDIO OVER SINGLE FIBER EXTENDER
SPECIFICATIONS
Input Power 12VDC/1.5A, DC Plug 2.1mm
Power Adapter 90-240VAC
Optic Fiber 50/125u multimode, 62.5/125u multimode, 9/125u singlemode
Signal to Noise Ratio >85dB
Input Impedance 10K - 20K
Power Consumption <5W
Max Line Input Voltage 6.9Vp-p
Line Level 0dB in / 0dB out
Frequency Response 20Hz—20KHz
Sample Rate 48KHz
Latency Delay 272us
Unit Dimensions Each Unit 4.33 x 3.62 x 1.65 in / 110mm x 92mm x 42mm
Weight Each Unit 7.9 oz / 224 g
Includes 2-AC 12VDC/1.5A Power Adapters & 2-9V Batteries Power Adapters


Produkt Specifikationer

Mærke: Sescom
Kategori: Audio/video konverter
Model: SES-X

Har du brug for hjælp?

Hvis du har brug for hjælp til Sescom SES-X stil et spørgsmål nedenfor, og andre brugere vil svare dig




Audio/video konverter Sescom Manualer

Audio/video konverter Manualer

Nyeste Audio/video konverter Manualer