Silent Knight SD500-AIM Manual

Silent Knight Detektor SD500-AIM

Læs gratis den danske manual til Silent Knight SD500-AIM (2 sider) i kategorien Detektor. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Silent Knight SD500-AIM, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
P/N 151071
SD500-AIM Input Module and
SD500-MIM Mini Input Module
Installation Instructions
The following instructions are a quick reference
guide, refer to the control panel installation
manual P/N 151139, 151274, 151280, 151295,
151209, or 151302 for detailed system
information.
Wiring the SD500-AIM / MIM
Note: Installation and wiring of these devices must be done in
accordance with NFPA 72 and local ordinances.
Terminate the wiring as shown in Table 1. See
also Figure 1 or Figure 2
Specifications
Table 2 lists the operating specifications for the
SD500-AIM and the SD500-MIM.
Impedance for Earth Ground Fault is 0 Ω for all
terminals.
Figure 1: Class B Wiring the SD500-AIM & SD500-MIM
Table 1: Wire Connections
SD500-AIM
SD500-MIM
Terminals
To:
FACP or SLC
Loop Terminals Contact
SLC –SLC
OUT
SC–
+ S+
Contact
A out CLASS A
OR B
To N.O. Contact
B out To N.O. Contact
A IN CLASS A ONLY
(SD500-AIM Only)
End of Loop A
End of Loop B
B IN
Table 2: SD500-AIM and SD500-MIM Specifications
Specifications
Max. Line resistance 50Ω
Max. Alarm
Current
One device in alarm
23mA. 46 mA for two
devices in alarm.
.5 mA for each addi-
tional device in
alarm.
Max. Voltage 33 V
Operating Temperature 0° to 49° C
(32° to 120° F)
Indoor use only
Table 2: SD500-AIM and SD500-MIM Specifications
Specifications
Alternate
Construction
SD500-AIM Input Module and SD500-MIM Mini Input Module Installation Instructions
2
7550 Meridian Circe, Suite 100
Maple Grove, MN 55369-4927
763-493-6455 or 800-328-0103
Fax: 763-493-6475
www.silentknight.com
© 2008 Honeywell International Inc. PN 151071 Rev G
Figure 2: Class A Wiring the SD500-AIM
Mounting the SD500-AIM
Mount the SD500-AIM into a double gang box
as shown in Figure 3.
Mounting the SD500-MIM
Install the SD500-MIM into a single gang box
see Figure 1 and Figure 3.
Figure 3: Mounting the SD500-AIM and SD500-MIM
Setting the Devices Address
The range of valid addresses is 1 - 127 (0 is an
invalid address). Refer to Figure 4 to set the dip
switches to the desired address.
Figure 4: Setting the Device Address:
Note: The dip switch settings shown in Figure 4 apply to the
SD500-MIM also.
Status LED

Produkt Specifikationer

Mærke: Silent Knight
Kategori: Detektor
Model: SD500-AIM

Har du brug for hjælp?

Hvis du har brug for hjælp til Silent Knight SD500-AIM stil et spørgsmål nedenfor, og andre brugere vil svare dig


Detektor Silent Knight Manualer

Silent Knight

Silent Knight SD500-MIM Manual

30 August 2024
Silent Knight

Silent Knight SD505-6IB Manual

30 August 2024
Silent Knight

Silent Knight SD500-SDM Manual

30 August 2024
Silent Knight

Silent Knight SD500-AIM Manual

30 August 2024
Silent Knight

Silent Knight SD500-ARM Manual

30 August 2024
Silent Knight

Silent Knight SD500-ANM Manual

30 August 2024

Detektor Manualer

Nyeste Detektor Manualer

Safescan

Safescan 70 Manual

15 Juni 2025
Safescan

Safescan 1250 Manual

15 Juni 2025
Safescan

Safescan 50 Manual

15 Juni 2025
Safescan

Safescan 55 LED Manual

14 Juni 2025
Safescan

Safescan 185-S Manual

14 Juni 2025
Craftfull

Craftfull XPoser Mini Manual

30 Marts 2025
Bounty Hunter

Bounty Hunter Tracker IV Manual

27 Marts 2025
Satel

Satel PERFECTA-IP32 Manual

20 Marts 2025
Satel

Satel TESTER INDIGO Manual

14 Marts 2025
Conrad

Conrad GC1026 Manual

8 Marts 2025