Silent Knight SD500-ANM Manual

Silent Knight Detektor SD500-ANM

Læs gratis den danske manual til Silent Knight SD500-ANM (2 sider) i kategorien Detektor. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Silent Knight SD500-ANM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

P/N 151109

SD500-ANM

Installation Instructions

The following instructions are a quick reference

guide, refer to the control panel installation

manual for detailed system information.

The SD500-ANM (Addressable Notification

Module) is an output accessory module for the

IntelliKnight Fire Control Panel, which provides

one reverse polarity supervised notification

appliance circuit. The notification circuit can be

configured in either Class A (Style Z) or Class B

(Style Y).

SD500-ANM Specification

Table 1 list the electrical, physical and

environmental specifications of the SD500-

ANM.

Note: When calculating total alarm current, add the

current ratings of all the notification devices on the

notification circuit.

Wiring the SD500-ANM

Note: Installation and wiring of this device must be done

in accordance with NFPA 72 and local ordinances.

Important!: All wiring is supervised and power limited.

Connecting SD500-ANM to the SLC

The SD500-ANM connection for the SLC loop

internal and external are the same. Wire as

shown in Figure 1.

Figure 1: SD500-ANM Connections to the 5815XL

Table 1: SD500-ANM Specs

Specification Parameter Rating

Operating Temperature: 32° - 120° F

(0° - 49° C)

Dimensions:

Length: 4-7/8”

Width: 4-7/8”

Depth: 7/8”

Operating Voltage: 24 VDC

Notification Appliance Current: 2 A max.

Notification Outputs 24 VDC

Full Wave Rectified

SLC Current: .55 mA

Max. SLC Loop Resistance: 50 Ω

Max Impedance Output 1.5 Ω

For indoor use only

Model SD500-ANM Installation Instructions

7550 Meridian Circle

Maple Grove, MN 55369-4927

763-493-6455 or 800-328-0103

Fax: 763-493-6475

www.silentknight.com

Class B Notification Configuration

Wire Class B notification appliance circuits to

the SD500-ANM as shown in Figure 2.

Figure 2: SD500-ANM Class B Notification Wiring

Class A Notification Configuration

Wire Class A notification appliance circuits to

the SD500-ANM as shown in Figure 3.

Figure 3: SD500-ANM Class A Notification Wiring

Auxiliary Power Using

Flexput™ Circuits

The SD500-ANM can use aux power from any

24 VDC source. The following describes how to

use the Flexput circuits as the auxiliary power

source:

1. Connect the aux power wires to the Flexput

terminals using “X” terminals as positive

and “O” terminals as negative power. See

Figure 4.

Figure 4: Flexput Auxiliary Power Output

2. Configure the auxiliary power output for

constant output through programming. Refer

to the control panel installation manual for

programming information.

UL listed

4.7 kΩ EOL

Model 7628

Produkt Specifikationer

Mærke:	Silent Knight
Kategori:	Detektor
Model:	SD500-ANM

Har du brug for hjælp?

Hvis du har brug for hjælp til Silent Knight SD500-ANM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Detektor Silent Knight Manualer

Silent Knight SD500-MIM Manual

30 August 2024

Silent Knight SD505-6IB Manual

30 August 2024

Silent Knight SD500-SDM Manual

30 August 2024

Silent Knight SD500-AIM Manual

30 August 2024

Silent Knight SD500-ARM Manual

30 August 2024

Silent Knight SD500-ANM Manual

30 August 2024

Detektor Manualer

Nyeste Detektor Manualer

Safescan 70 Manual

15 Juni 2025

Safescan 1250 Manual

15 Juni 2025

Safescan 50 Manual

15 Juni 2025

Safescan 55 LED Manual

14 Juni 2025

Safescan 185-S Manual

14 Juni 2025

Craftfull XPoser Mini Manual

30 Marts 2025

Bounty Hunter Tracker IV Manual

27 Marts 2025

Satel PERFECTA-IP32 Manual

20 Marts 2025

Satel TESTER INDIGO Manual

14 Marts 2025

Conrad GC1026 Manual

8 Marts 2025