Silent Knight SD500-SDM Manual

Silent Knight Detektor SD500-SDM

Læs gratis den danske manual til Silent Knight SD500-SDM (4 sider) i kategorien Detektor. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 28 anmeldelser. Har du et spørgsmål om Silent Knight SD500-SDM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

P/N 151193

SD500-SDM Installation

Instructions

The SD500-SDM two-wire smoke module

allows you to connect a loop of conventional

detectors to a Silent Knight addressable fire

alarm control panel (FACP). Each loop can then

be assigned an address on the FACP.

Specifications

Compatibility

The SD500-SDM is compatible with all Silent

Knight addressable FACPs.

Wiring

Note: Installation and wiring of this device must be done in

accordance with NFPA 72 and local ordinances.

Important! All wiring is supervised and power limited.

Connecting the SD500-SDM

to the SLC Loop

The SD500-SDM connections to the 5815XL

internal and external are the same. Wire as

shown in Figure 1.

Figure 1: SLC Wiring

Smoke Detector Connections

This section contain instructions on how to

connect a 2-wire conventional smoke detector

loop to the SD500-SDM for either Class B (Style

B), or Class A (Style D).

Specification Parameter Rating

2-Wire Smoke Detector

Loop Current:

Standby: 2 mA max.

Alarm: 100 mA max.

Operating Voltage: SLC 32 VDC

Aux Power 24 VDC

SLC Current for battery

calculation:

Alarm: .55 mA

Standby: .55 mA

Operating Temperature: 32° - 120° F

(0° - 49° C)

Humidity: 10-85% RH

Max. SLC Loop Resistance: 50 Ω

Max. 2-wire Conventional Smoke Loop

Resistance

50 Ω

Dimensions: Length: 4-7/8”

Width: 4-7/8”

Depth: 7/8”

For indoor use only

SD500-SDM Installation Instructions

2 P/N 151193

Class B (Style B) Wiring

Wire Class B (Style B) conventional smoke

detector loop to the SD500-SDM as shown in

Figure 2. Place the jumper block in the Class B

(Style B) supervision position (see Figure 4).

Figure 2: Class B (Style B) 2-Wire Detector Loop

Note: Auxiliary power is supplied by a Regulated UL listed

power supply for Fire Protective Signalling Systems.

Class A (Style D) Wiring

Wire Class A (Style D) conventional smoke

detector loop to the SD500-SDM as shown in

Figure 3. Place the jumper block in the Class A

(Style D) supervision position (see Figure 4).

Figure 3: Class A (Style D) 2-Wire Detector Loop

Figure 4: Supervision Selection Jumper

Auxiliary Power Using

Flexput™ Circuits

The SD500-SDM can use aux power from any

24 VDC source. The following describes how to

use the Flexput circuits as the auxiliary power

source:

1. Connect the aux power wires to the Flexput

terminals using “X” terminals as positive

and “O” terminals as negative power. See

Figure 5.

Figure 5: Flexput Auxiliary Power Output

2. Configure the auxiliary power output for

constant output through programming. Refer

to the FACP installation manual form more

information.

For More Information

This document is for quick reference. For more

information, refer to the FACP installation

manual.

Produkt Specifikationer

Mærke:	Silent Knight
Kategori:	Detektor
Model:	SD500-SDM

Har du brug for hjælp?

Hvis du har brug for hjælp til Silent Knight SD500-SDM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Detektor Silent Knight Manualer

Silent Knight SD500-MIM Manual

30 August 2024

Silent Knight SD505-6IB Manual

30 August 2024

Silent Knight SD500-SDM Manual

30 August 2024

Silent Knight SD500-AIM Manual

30 August 2024

Silent Knight SD500-ARM Manual

30 August 2024

Silent Knight SD500-ANM Manual

30 August 2024

Detektor Manualer

Nyeste Detektor Manualer

X-Sense Pro XH01-W Manual

30 Juli 2025

Hikvision ISD-SMG1112L Manual

28 Juli 2025

Hikvision ISD-SMG1118L Manual

28 Juli 2025

Uniden GRAN ALCANCE R3 Manual

27 Juli 2025

STI -8230-W Manual

25 Juli 2025

Edimax AI-2005BE Manual

24 Juli 2025

Milwaukee 2200-20 Manual

22 Juli 2025

Steinberg SBS-MD-20 Manual

19 Juli 2025

Steinberg SBS-MD-8 Manual

19 Juli 2025

Steinberg SBS-MD-4 Manual

19 Juli 2025