Sloan ESD-2000 Manual

Sloan Sæbedispenser ESD-2000

Læs gratis den danske manual til Sloan ESD-2000 (4 sider) i kategorien Sæbedispenser. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Sloan ESD-2000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

SLOAN DECK MOUNTED SOAP DISPENSER (ESD-SERIES) INSTALLATION INSTRUCTIONS

Touchfree Counter Mounted System Installation Guide

If there is a dispenser currently installed

• Remove the existing unit, both the above and below counter assemblies

• Clean the counter area where the previous dispenser was located

• Verify the size of the existing counter hole is 15/16” to 1-1/4” in diameter

If there is no hole in the counter

• Prior to drilling, examine below the counter to ensure adequate clearance for the new unit

• Drill a 1” diameter hole in the counter top

• The hole can be drilled to either the right or left of the faucet, ensuring adequate clearance for the below counter assembly

• Clean the counter area where the new hole is located

Code no. 0816203

Rev1 (01/17)

Prior To Installation

New Soap Dispenser Installation:

• Ensure that dispenser does not interfere with anything

above or below the lavatory/counter top area

• Drill a 1” diameter hole in counter top

• Clean area around hole

To Order Replacement Soap Cartridges

800.321.9647

GOJO Industries

Rells are also available through your local plumbing or janitorial supply

distributor.

When the soap bottle is empty, a new bottle must be used. The bottle

furnished with the unit is not designed to be relled. Altering the bottle and

relling it with soap will void the warranty of the product.

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants its Products to be made of rst class materials, free from defects of material or workmanship under

normal use and to perform the service for which they are intended in a thoroughly reliable and efcient manner when properly installed and serviced, for

a period of three years (1 year for SF Faucets, special nishes and PWT electronics and 30 days on PWT software) from date of purchase. During this

period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at

customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs.

This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of

resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY

RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

SLOAN • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131

Phone: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380 • www.sloan.com

Improper installation of the

Counter Mounted Dispenser

could result in

breakage.

Dispenser must hang freely

underneath the sink.

Proper installation allows

the unit to vertically hang

beneath the sink.

ESD-1500

ESD-2000

ESD-500

ESD-600 ESD-700 ESD-800

ESD-2100

Soap Dispenser Installation

NOTE: ESD-2100 Shown, instructions applicable for all Sloan soap dispensers

Installing the Touchfree Counter Mounted System

Prior to beginning installation, study the exploded view of the Touchfree Counter-Mounted System and locate all the

pieces. Also, look beneath the countertop to and a suitable place for mounting of the Battery Box (9) so that it will not

interfere with system components or plumbing.

Feed the Data Cable 5a and the

shank of the Dispenser Assembly

1 through the hole in the

countertop. Point the spout of the

Dispenser into the sink bowl.

From underneath the counter,

feed the Lock Washer 3 and then

the Mounting Nut 3a over the

Data Cable 5a and onto the

threaded shank of the Dispenser

Assembly 1. Tighten the nut

securely.

Align the indent inside the top of

the Motor Assembly/Bottle

Support 7 with the indent on the

shank of the Dispenser Assembly

1 and rmly push the Motor

Assembly/Bottle Support up, onto

the shank.

NOTE: Hold the Data Cable rmly

out of the way as you push up on

the Motor Assembly/Bottle

Support. Continue pushing

upward until the vertical slots in

the Dispenser shank and the

Motor Assembly/Bottle Support

line up.

Secure the Motor Assembly/Bottle

Support 7 to the Dispenser

Assembly 1 shank by pushing the

Retaining Clip 4 into place

through the vertical slots, until it

goes all the way through the Motor

Assembly.

NOTE: Motor Assembly Bottle

Support will rotate 360° to avoid

any obstruction.

Remove the cover from the

Battery Box 8 by loosening the

two captive screws on the Battery

Box cover. Position the Box on a

convenient (vertical or horizontal)

surface under the counter top that

will allow access for battery

changing. Attach the Box to the

surface using the two screws 10

and anchors (if attaching to a

plaster or masonry surface).

Use the Wall Clip 11 to secure the

Power Cable to a wall or other

under-counter surface if desired.

Place four alkaline “D” Cell

batteries into the Battery Box 9

cover. The batteries must be

positioned according to the

diagrams shown on the inside of

the cover.

NOTE: If the batteries are not

properly installed or the cover is

not properly positioned on the

Box, the System will not work.

Position the cover (with batteries

installed) on the Battery Box and

tighten the two captive screws.

IMPORTANT: Connect the two

halves of the Data Cable 5a

and 5b

by visually lining up the white

stripes on each half and gently

pushing the cable connectors

together until the stripes touch.

Improperly assembled

connectors can cause unit to

not function as intended.

After the batteries are installed in

the battery box, connect the two

halves of the power cable 6a and

6b . Allow 20 seconds before the

system is ready to dispense soap.

Produkt Specifikationer

Mærke:	Sloan
Kategori:	Sæbedispenser
Model:	ESD-2000

Har du brug for hjælp?

Hvis du har brug for hjælp til Sloan ESD-2000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Sæbedispenser Sloan Manualer

Sloan ESD-250 Manual

16 Juni 2025

Sloan ESD-500 Manual

15 Juni 2025

Sloan ESD-2000 Manual

15 Juni 2025

Sæbedispenser Manualer

Nyeste Sæbedispenser Manualer

Teesa TSA8076 Manual

2 Oktober 2025

Waterloo 750EFDMSDC Manual

29 September 2025

Waterloo 750EFDMSDBK Manual

29 September 2025

Simplehuman ST1015 Manual

26 September 2025

Bradley WBD1-0019 Manual

17 September 2025

Tork Elevation S4 Manual

29 August 2025

Tork S1 Manual

29 August 2025

Tork S2 Manual

28 August 2025

Tork H3 Manual

28 August 2025

Bradley WBD1-0011 Manual

26 August 2025