Sonneman Chimes 2046 Manual

Sonneman Lys Chimes 2046

Læs gratis den danske manual til Sonneman Chimes 2046 (3 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Sonneman Chimes 2046, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Assembly Instructions

Chimes

Product Information

and Warnings

2046

Round Pendant

IMPORTANT

Always disconnect the power before installing or replacing

Luminaires and before cleaning or other maintenance.

Consult a qualied, licensed electrician to ensure correct branch

circuit conductor.

Consulter un électricien qualié pour vous assurer que les

conducteurs de la dérivation sont adéquats.

Please read all included assembly instructions and warnings carefully

before installation. Contact Customer Service if you have any

questions or concerns. Before installation, please confirm that the

fixture is compatible with your supply voltage and dimming system,

if present.

LEDs are highly sensitive electronic devices, and must be treated

with care. Do not open any factory sealed compartments, and avoid

touching the LEDs with your hands or any object.

Although all our fixtures are equipped with protective devices,

LED electronic systems are vulnerable to power surges and supply

variations. Do not install LED fixtures on the same circuit as any

motors, appliances, or HVAC systems.

Do not remove or bypass any LED Driver or Transformer that is

provided with the fixture, and do not replace or substitute with

another power supply.

Fixtures must be wired in parallel on independent leads; do not

"daisy chain" multiple fixtures together or wire them in series.

All factory-made splices and connections must remain intact. LED

circuits are carefully designed and built, and improper connections

may damage the fixture.

The ends of coaxial pendant cords have been precisely stripped

and split at the factory and must not be field cut. Excess cord or

cable should be neatly coiled and reserved in the fixture canopy.

Any mounting hardware is provided for your convenience

and should be used with discretion. Always use the appropriate

hardware for the mounting surface.

Instructions D'Installation

Multiple U.S. and foreign patents pending.

Assembly Instructions

a. Connect the power supply’s live wire to the live supply

wire.

b. Connect the power supply’s neutral wire to the neutral

supply wire.

c. Connect the xture’s ground wire (green or uncoated)

to the ground supply wire. If no ground wire is present

in the outlet box, connect the power supply's ground

wire to the mounting plate (B) using the green screw

(included).

6. Fit the canopy (H) over the mounting plate (B), tucking any

loose wire or cable inside, so that the threaded rod extends

through the center hole. Screw the canopy nut (J) onto the

threaded rod to secure the canopy.

7. Restore power to the outlet box (C).

1. Shut o power to the outlet box (A).

2. CAUTION: Fixture must be supported independent of the

outlet box. Customer is responsible for ensuring appropriate

ceiling construction to support the wieght of the xture.

3. Attach the mounting plate (B) to the outlet box (A) with the

outlet box screws (C). Secure the plate to the ceiling using

the 4 supplied lag screws (D) or other appropriate hardware

for other surfaces.

4. Determine height at which the xture is to be hung. Note

that this xture hangs from three steel cables. The power

cords should not bear weight.

a. Adjust the 3 steel cables to the desired height: To shorten

the cable, push the cable up and it will lock automatically.

To lengthen the cable, lift up on the cable and push up

on the plunger lock (F). While keeping the plunger lock

depressed, lower the cable to the desired length. Release

the plunger lock to set. Adjust the position of the cable

lock (E) close to the cable gripper and tighten the screws.

Reserve extra cable in the canopy (H).

b. Adjust the 2 power cords to the desired length: Use the

Allen wrench to loosen the set screw (G). Adjust length

of power cord. Tighten the set screw to set. Reserve extra

cord in the canopy (H).

c. The location of the spreader ring (K) inside the xture

should not need to be adjusted. In the case that it requires

adjustment, you may loosen the set screws, adjust the

cables and power cords, and re-tighten the set screws.

5. Make appropriate electrical connections to the power

supplies (I) using wire nuts:

Care Instructions:

Use a clean, dry cloth when dusting.

To protect the nish, avoid any harsh

abrasives or chemicals.

Note:

• This xture is dimmable with Electronic Low Voltage (Trailing-Edge)

type dimmers, Incandescent (Leading-Edge) type dimmers, and

0-10V type dimmers only.

(D) (G)

(B)

(C)(I)

(A)

(F)

(H)

(J)

(K)

(E)

Produkt Specifikationer

Mærke:	Sonneman
Kategori:	Lys
Model:	Chimes 2046

Har du brug for hjælp?

Hvis du har brug for hjælp til Sonneman Chimes 2046 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Sonneman Manualer

Sonneman Offset 2759 Manual

5 Juli 2025

Sonneman Lithe 3468 Manual

4 April 2025

Sonneman Chimes 2046 Manual

2 April 2025

Sonneman Lithe 3456 Manual

2 April 2025

Sonneman Suspenders SLS0163 Manual

13 November 2024

Sonneman Suspenders SLS0157 Manual

13 November 2024

Sonneman Stix Plus 2790.16 Manual

17 September 2024

Sonneman Stix 2772.16 Manual

11 September 2024

Lys Manualer

Nyeste Lys Manualer

3 Oktober 2025

3 Oktober 2025

3 Oktober 2025

3 Oktober 2025

BeamZ Cobra 100H Manual

3 Oktober 2025

BeamZ IGNITE 300 Manual

2 Oktober 2025

BeamZ BAC550Z Manual

2 Oktober 2025

BeamZ SB420IP Manual

2 Oktober 2025

BeamZ Mimas Laser Manual

2 Oktober 2025

BeamZ Phantom 2000 Manual

2 Oktober 2025