Starlight Xpress Lodestar PRO Manual

Starlight Xpress Ikke kategoriseret Lodestar PRO

Læs gratis den danske manual til Starlight Xpress Lodestar PRO (11 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Starlight Xpress Lodestar PRO, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/11
Lodestar PRO C handbook Issue 2, February 2024
Handbook for the SX ‘Lodestar PRO C’
Imaging and Guiding Camera
Thank you for purchasing a Starlight Xpress ‘ ’ camera. We hope that you will be Lodestar PRO Colour
very pleased with the performance of this product.
imager/guider, which is powered and operated via a single USB2.0 computer connection. It also
provides an opto-isolated output connection for direct control of most mounts, via their ‘Autoguider’
sockets. This output is compatible with the ‘ST4’ style of RJ12 connection and supplies 4 ‘pull down’
direction lines and a common return. Alternatively, you may send the mount control signals via a
serial connection from the guider control computer. The Lodestar PRO C utilises a very sensitive Sony
‘ExView2’ CCD (the ICX829AK) with an array of 752 x 580 pixels in a ‘half inch’ format. Although the -
chip is not cooled, it has a very low dark signal and very little readout noise, so it can be used to guide
on faint stars that are well beyond the reach of webcams and CMOS chip based guide cameras.
Lodestar PRO C handbook Issue 2, February 2024
The Lodestar PRO Colour specification:
CCD - Sony ICX829AK ExView2 colour CCD
Pixel count - 752(H) x 580(V)
Pixel size - 8.6 x 8.3uM
Optical size - 6.47 x 4.81 mm
Colour filter grid - RGGB Bayer Matrix
Read noise - Typically electrons 8
Gain - 8 e/ADU 0.
Barrel size - 31.75mm dia. x 85mm long (1.25 inch eyepiece push fit size)
Barrel thread - 25.4mm x 0.75mm ‘CS’ mount lens thread
Input connection - ‘Mini B’ USB socket for USB2.0
Output connection - Standard RJ12 autoguider socket
Output type - Opto-isolated 4 lines (N,S,E & W) pull down with common return line
Download rate - Approx. 10 frames per second in binned 2x2 mode (recommended)
Installing the Lodestar PRO C:
Before connecting the Lodestar PRO to your computer, please install the appropriate drivers for C
your operating system from the USB drive supplied with your camera.
The supplied USB stick contains all the drivers and software. To install the drivers:
1. Select the folder for your operating system
2. Double click on the “Install Drivers.exe”
3. Follow the prompts in the installer and click ‘Finish’ at the end of the install.
If you encounter any problems, read the README file on the USB drive or you can download the latest
drivers from our web page at https://www.sxccd.com/drivers-downloads.
The Lodestar PRO C control software is Lodestarc_usb.exe. To install this:
1. Double click on the Colour Lodestar Software folder on the USB drive.
2. Double click on the Setup.exe program
3. Follow the prompts to fully install the software on to your computer.
4. Plug in your Lodestar PRO C camera (Wait for the Install New Hardware Wizard to –
complete)
5. Double click on the Lodestarc_usb.exe icon on your Desktop or from your START button on
your computer.
6. The first time you use the software, click on “File” then “Set Program Defaults” You will get a
message, “Warning – – Please set defaults” No INI File found
7. Click “OK” – The Set Program Defaults box will appear.
8. If you are going to be using the RJ12 Autoguider Port on your Lodestar X2C, select
Autoguider Socket in the “Telescope Guiding Parameters” box at the top of this box.
9. Click on “Save Changes” and you are all set to start using the camera. (The INI file that was
being asked for initially has now been created and you will no longer see the Warning
message)
To install Starlight Live (‘Live stacking’) software:-
1. Double click on the Starlight Live folder on the USB drive.
2. Double click on the Setup.exe program
3. Follow the prompts to fully install the software on to your computer.
4. Plug in your Lodestar PRO C camera (Wait for the Install New Hardware Wizard to –
complete)
5. Double click on the Starlight Live.exe icon on your Desktop or from your START button on
your computer.

Produkt Specifikationer

Mærke: Starlight Xpress
Kategori: Ikke kategoriseret
Model: Lodestar PRO

Har du brug for hjælp?

Hvis du har brug for hjælp til Starlight Xpress Lodestar PRO stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Starlight Xpress Manualer

Starlight Xpress

Starlight Xpress SX Spectrograph PRO Manual

6 Juli 2025
Starlight Xpress

Starlight Xpress Ultrastar PRO Manual

6 Juli 2025
Starlight Xpress

Starlight Xpress TRIUS PRO-674C Manual

6 Juli 2025
Starlight Xpress

Starlight Xpress Lodestar PRO Manual

1 April 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

FiiO

FiiO Retro Nano Manual

6 Oktober 2025
Metra

Metra AX-NIS24SWC-6V Manual

6 Oktober 2025
Clarion

Clarion NX403A Manual

6 Oktober 2025
Metra

Metra 95-6555B Manual

6 Oktober 2025
Clarion

Clarion VT1510E Manual

6 Oktober 2025
Gamko

Gamko KFK/2CS Manual

6 Oktober 2025
Rapid

Rapid RP150 Multi Manual

6 Oktober 2025
Electro Harmonix

Electro Harmonix Stereo Memory Man with Hazarai Manual

6 Oktober 2025
Electro Harmonix

Electro Harmonix Next Step Volume Pedal Manual

5 Oktober 2025
Zoom

Zoom 504II Manual

5 Oktober 2025