Sun Joe BDL-A0203 Manual

Sun Joe Sav BDL-A0203

Læs gratis den danske manual til Sun Joe BDL-A0203 (76 sider) i kategorien Sav. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Sun Joe BDL-A0203, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/76
© 2021 by Snow Joe
®
, LLC
All rights reserved. Original instructions.
1
SAVE THESE INSTRUCTIONS
EN
A Division of Snow Joe
®
, LLC
R
OPERATOR’S MANUAL
Model 24V-PS10-LTE Form No. SJ-24V-PS10-LTE-880E-MR1
CORDLESS POLE CHAIN SAW
24-VOLT MAX* | 2.0 Ah | 10-INCH
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Safety
m
WARNING! This appliance is not intended for use
by children or by unassisted, unsupervised persons whose
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure that
they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe
®
+ Sun Joe
®
dealer or
call the Snow Joe
®
+ Sun Joe
®
customer service center at
1-866-SNOWJOE (1-866-766-9563).
mWARNING! When using the power tool, basic safety
precautions should always be followed to reduce the risk of
re, electric shock, and personal injury. These include:
1. Keep guards in place – Protective guards should be
checked periodically to ensure they are properly tted and
in correct working order.
2. Keep work area clean and well-lit – Clear work area of
branches and limbs after each cutting session. Cluttered
areas invite accidents.
3. Do not use in dangerous environments – Do not use
power tools in damp or wet locations.
4. Do not use the pole chain saw in the rain – Do not use
the pole saw in bad weather conditions, especially when
there is a risk of lightning. This decreases the risk of being
struck by lightning.
5. Keep bystanders and children away – All bystanders,
including children and pets, should be kept a safe
distance away from the work area.
6. Do not force the tool – It will do the job eectively and
safely if it is used at the rate for which it was designed.
7. Use the right tool – Do not force the tool or any
attachment on the tool to do a job for which they were
not designed.
8. Wear proper apparel – Do not wear loose articles of
clothing or jewelry since such items may get caught
in moving parts. Use of heavy-duty rubber gloves,
substantial non-skid footwear and close-tting clothing is
recommended when working outdoors with power tools.
9. Always use head protection when operating the pole chain
saw overhead. Falling debris can result in serious personal
injury.
10. Always wear safety glasses and ear defenders to
provide eye and ear protection – Everyday eyeglasses
only have impact resistant lenses and do not provide the
same protection as safety glasses.
11. Wear face or dust masks – If the cutting operation is
dusty, the use of a face or dust mask specially designed
to lter out microscopic particles is recommended.
12. Do not overreach – Keep proper footing and balance
at all times.
13. Maintain tools with care – Keep tools sharp and clean
for best and safest performance. Follow instructions for
lubricating and changing accessories.
14. Disconnect tool – Turn o the power switch and remove
the battery when it is not in use, before servicing, when
transporting or when changing the chain or
other accessories.
15. Reduce the risk of unintentional starting – Make sure
the safety lock button and the On/O switch are in the
OFF position before inserting the battery in the unit. Do
not carry the pole chain saw with the safety lock button
and the On/O switch engaged.
16. Use recommended accessories – Consult the owner’s
manual for recommended accessories. The use of
improper accessories may cause risk of injury.
17. Check for damaged parts – Before each use, repair or
replace any guard or part that is damaged. In addition,
check for alignment of moving parts, binding of moving
parts, breakage of parts and any other conditions that
may aect the tool's operation.
18. Never leave tool unattended while it is running – Turn
the power OFF and remove the battery from the unit.
Do not leave the saw until the cutting bar comes to a
complete stop.
19. Do not grasp the exposed cutting blade or cutting
edges when picking up or holding the saw – Be sure
to encase the cutting bar in its protective sheath when
not in use.
20. Stay alert – Watch what you are doing. Use common
sense. Do not operate the pole chain saw when you
are tired.

Produkt Specifikationer

Mærke: Sun Joe
Kategori: Sav
Model: BDL-A0203

Har du brug for hjælp?

Hvis du har brug for hjælp til Sun Joe BDL-A0203 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Sav Sun Joe Manualer

Sun Joe

Sun Joe BDL-A0203 Manual

10 August 2025
Sun Joe

Sun Joe 20VIONLTE-PS8-RM Manual

10 August 2025
Sun Joe

Sun Joe 24V-HCSWP-6-LTE Manual

29 Juli 2025
Sun Joe

Sun Joe SWJ802E-PRP Manual

14 November 2024
Sun Joe

Sun Joe 24V-CSSHRP-CT-RM Manual

1 Januar 2024
Sun Joe

Sun Joe SWJ599E-RM Manual

24 December 2023
Sun Joe

Sun Joe 24V-PS10-CT Manual

24 December 2023
Sun Joe

Sun Joe SWJ800E-RM Manual

16 December 2023
Sun Joe

Sun Joe 24V-CSSHRP-LTE-RM Manual

22 November 2023
Sun Joe

Sun Joe ION16CS-RM Manual

26 August 2023

Sav Manualer

Nyeste Sav Manualer

RIKON

RIKON 10-1414 Manual

1 November 2025
RIKON

RIKON 10-3062 Manual

31 Oktober 2025
Dedra

Dedra DED7338 Manual

31 Oktober 2025
SereneLife

SereneLife PSLTLL1516 Manual

19 Oktober 2025
Proviel

Proviel HFS 518 Manual

16 Oktober 2025
Proviel

Proviel TK 600 Manual

16 Oktober 2025
Hurricane

Hurricane ES 2040/1 S Manual

16 Oktober 2025
Hurricane

Hurricane MKS 38/41 Manual

16 Oktober 2025
Alpha Tools

Alpha Tools TK 1500 E Manual

13 Oktober 2025
Alpha Tools

Alpha Tools KS 250 Manual

13 Oktober 2025