V-TAC VT-77 Manual

V-TAC Lys VT-77

Læs gratis den danske manual til V-TAC VT-77 (15 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om V-TAC VT-77, eller vil du spørge andre brugere om produktet?

Side 1/15
WEEE Number: 80133970
INSTALLATION INSTRUCTION
LED SOLAR LIGHT
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
WARNING!
1. The light source of this luminaire is not replaceable;
when the light source reaches its end of life the whole
luminaire shall be replaced.
2. Installation should be done by certified electrician.
This marking indicates
that this product should
not be disposed of with
other household wastes
MULTI-LANGUAGE
MANUAL QR CODE
Please scan the QR code
to access the manual in
multiple languages.
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please
read these instructions carefully before starting the installation and keep this manual
handy for future reference. If you have any another query, please contact our dealer or
local vendor from whom you have purchased the product. They are trained and ready
to serve you at the best.The warranty is valid for 3 years from the date of purchase.
The warranty does not apply to damage caused by incorrect installation or abnormal
wear and tear. The company gives no warranty against damage to any surface due to
incorrect removal and installation of the product.
3
YEARS
WARRANTY
*
TECHNICAL SPECIFICATIONS
MODEL VT-77
WATTS 2W
LUMENS 220LM
BEAM ANGLE 170
CRI >80
IP RATING IP65
SOLAR LIGHT
EN
INSTALLATION DIAGRAM
Fixing
Bracket
Installation Instruction:
1. Drill two holes on the wall after confirming the installation position, then install the
expansion plug into the holes.
2. Put the screw into the expansion plug, do not screw to the end, it is ok if the screw
head is about 2-3mm away from the wall. If the installation surface is wood or soft
material, it can be screwed directly without using the expansion plug.
3. Put the mounting base into two screws on the wall. Then, tighten the base as
shown in Figure 1.
4. Install the lamp on the base, and it can be used.
Switch Function:
- Press and hold the button for 2-3 seconds to switch ON the solar light. Once
switched ON it will indicate a blue light.
- When switching on the solar light by default it will be in Mode 1.
- To enter Mode 2, press the button again.
- Pressing the button for the third time the solar light will switch OFF and the blue
light will disappear.
Operating Modes:
Mode 1: Sensor Mode
- At dusk, it automatically turns to 10% brightness.
- Turns on to 100% brightness when motion is detected in the range of <5 meters
- In 30 seconds if no motion is detected the light switches to 10% brightness.
- Turns off at the dawn.
Mode 2: Constant Brightness Mode
- The sensor will be disabled
- Automatically turns on at the dusk with 100% brightness and works constantly till
the battery capacity goes to Zero. (Upto 4 hours)


Produkt Specifikationer

Mærke: V-TAC
Kategori: Lys
Model: VT-77

Har du brug for hjælp?

Hvis du har brug for hjælp til V-TAC VT-77 stil et spørgsmål nedenfor, og andre brugere vil svare dig