Valcom VIP-822 Manual

Valcom Netværkskort/adapter VIP-822

Læs gratis den danske manual til Valcom VIP-822 (4 sider) i kategorien Netværkskort/adapter. Denne vejledning er vurderet som hjælpsom af 67 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 34 anmeldelser. Har du et spørgsmål om Valcom VIP-822, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
1 947998
ISSUE 3
VIP-822
DUAL NETWORKED TRUNK PORT
INTRODUCTION
The VIP-822 Dual Networked Trunk Port allows
most loop start station ports to be connected to a
SIP connectivity allows the VIP-821 to act as a
gateway device between a SIP telephone system
and the other Valcom paging systems, such as the
MultiPath.
SPECIFICATIONS
Access Methods
PBX, FXS Port
SIP
Features
RJ-45 for network connection
2 RJ-11 FXO connections
2 RJ-11 failover telephone connections
Decode Caller ID signals
Front panel activity LED
Network activity LEDs
2.5mm jack for DC power
Power over Ethernet (PoE) 802.3af compatible
Dimensions/Weight
(4.45cm H x 17.15cm W x 24.13cm D)
Weight: 1.75 lbs. (0.80 kg)
Nominal Specifications
Input Impedance: 600 Ohms
Input Level: -10dBm
Output Impedance: 600 Ohms
Output Level: - 10dBm nominal
Nominal Power Requirements
Via back panel barrel connector:
Voltage: 24VDC
Current: 325mA
Via 802.3af PoE Ethernet Switch:
802.3af: Class 3
Environment
Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating
Packing List
Qty Item
1 VIP-822
1 VSP Document
2 Mounting Brackets
4 Rubber Feet
INSTALLATION
NOTE: The telephone system referred to in this
manual is the customer premise equipment
such as an electronic key system, a PBX or a
dedicated single line telephone sets. The
VIP-822 is not intended for direct or indirect
connection to the public telephone network.
When used with a customer premise telephone
system such as a key system or PBX system,
these units are interfaced to the system via a
fully protected page port or system central
office port, which is a fully protected interface
device. Also, the host system must be
configured to disallow central office trunk
conferencing in order to prevent indirect
connection to the public network.
2 947998
Precautionary Designations
FCC Information
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses and can radiate radio
frequency energy and if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment
in a residential area may cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
Mounting
The VIP-822 is designed for wall, table or rack
mounting.
Table: Provided with the VIP-822 are four rubber
pads. Peel pads from their carrier backing and
place at the four corners of the bottom of the unit.
Wall: Using the template on last page of this
document, mark the location of the bracket screw
holes on the wall. Drill 5/64" pilot holes, 3/4" deep,
at each screw location and use the wood screws
provided to attach the brackets to the wall. For
surfaces other than wood, use hardware
appropriate for the surface (not included). With the
brackets securely attached to the wall, attach the
VIP-822 to the brackets using the included
hardware. Figure 2 illustrates the bracket
assembly.
Rack: Following the assembly drawing, attach the
two mounting brackets to the VIP-812 unit. Using
rack screws, mount the VIP-812 in an available 1U
rack slot. See Figure 1.
Power Connections
The preferred method of powering a VIP-822 is via
a Power over Ethernet (PoE) switch meeting the
802.3af specification.
If the rear panel barrel connector is used for power,
the preferred power supply is a Valcom VIP-324D.
Make all required signal connections before
applying power to the unit. If powering via 802.3af,
make sure all signal connections via the back
panel are made then connect the VIP-822 to the
Ethernet switch.
If power is supplied via the barrel connector, make
sure all signal connections are secure. Attach the
unit to the network via the front panel RJ-45
Ethernet connector. Apply power by plugging the
power supply into the VIP-822 via the barrel
connector on the rear of the VIP-822.
Network Connection
The VIP-822 has one RJ-45 network connector on
the front panel.
Use a standard Ethernet patch cable to connect
the VIP-822 to an Ethernet switch. If the Ethernet
switch is 802.3af compliant, the VIP-822 will draw
power from it.

Produkt Specifikationer

Mærke: Valcom
Kategori: Netværkskort/adapter
Model: VIP-822

Har du brug for hjælp?

Hvis du har brug for hjælp til Valcom VIP-822 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Netværkskort/adapter Valcom Manualer

Valcom

Valcom Station Port VIP-811 Manual

6 September 2024
Valcom

Valcom VIP-822 Manual

6 September 2024
Valcom

Valcom Trunk Port VIP-821 Manual

6 September 2024
Valcom

Valcom Trunk Port VIP-824 Manual

6 September 2024
Valcom

Valcom VIP-812 Manual

6 September 2024
Valcom

Valcom VIP-814 Manual

6 September 2024

Netværkskort/adapter Manualer

Nyeste Netværkskort/adapter Manualer

AMX

AMX CC-NIRC Manual

14 September 2025
AirTies

AirTies Air 2310 Manual

14 September 2025
Billion

Billion BIPAC P104 Manual

13 September 2025
Mercusys

Mercusys MA30N Manual

12 September 2025
Intellinet

Intellinet 561952 Manual

11 September 2025
Moxa

Moxa OnCell 5004-HSDPA Manual

3 September 2025
TRENDnet

TRENDnet TBW-107UB Manual

28 August 2025
Netgear

Netgear GSM4210PD Manual

23 August 2025
Advantech

Advantech FWA-1320 Manual

23 August 2025
Advantech

Advantech WISE-4050-AE Manual

23 August 2025