Valcom Trunk Port VIP-821 Manual

Valcom Netværkskort/adapter Trunk Port VIP-821

Læs gratis den danske manual til Valcom Trunk Port VIP-821 (3 sider) i kategorien Netværkskort/adapter. Denne vejledning er vurderet som hjælpsom af 73 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 37 anmeldelser. Har du et spørgsmål om Valcom Trunk Port VIP-821, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

1 947970

ISSUE 4

VIP-821

NETWORKED TRUNK PORT

INTRODUCTION

The VIP-821 Networked Trunk Port allows most

loop start terminal devices to be connected to a

managed IP-based LAN/WAN.

SIP connectivity allows the VIP-821 to act as a

gateway device between a SIP telephone system

and the other Valcom paging systems, such as

the MultiPath.

SPECIFICATIONS

Access Methods

 PBX, FXS Port

 SIP

Features

 RJ-45 for network connection

 1 RJ-11 FX0

 1 RJ-11 telephone failover connection

 Front panel activity LED

 Network activity LEDs

 2.5mm jack for DC

 802.3af compliant

Dimensions/Weight

 1.38 H x 6.13" W x 5.25" D

(3.50cm H x 15.6cm W x 13.33cm D)

 Weight: 1.25 lbs. (0.57 kg)

Nominal Specifications

Input Impedance: 600 Ohms

Input Level: -10dBm

Output Impedance: 600 Ohms

Output Level: - 10dBm nominal

Nominal Power Requirements

Via rear panel barrel connector:

Voltage: 24VDC

Current: 325mA

Via 802.3af PoE Ethernet Switch:

802.3af: Class 3

Environment

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

Packing List

Qty Item

1 VIP-821

1 VSP Document

2 Mounting Brackets W/Hardware

4 Rubber Pads

INSTALLATION

NOTE: The telephone system referred to in

this manual is the customer premise

equipment such as an electronic key system,

a PBX or a dedicated single line telephone

sets. The VIP-821 is not intended for direct or

indirect connection to the public telephone

network. When used with a customer premise

telephone system such as a key system or

PBX system, these units are interfaced to the

FXS or single line station port, which is a fully

protected interface device. Also, the host

system must be configured to disallow central

office trunk conferencing in order to prevent

indirect connection to the public network.

2 947970

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

Precautionary Designations

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses and can radiate

radio frequency energy and if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference in which case the user

will be required to correct the interference at

his own expense.

Mounting

The VIP-821 is designed for wall or table

mounting.

Wall: Using the bracket and screws provided,

secure the VIP-821 to the wall.

Table: Provided with the VIP-821 are four rubber

pads. Peel the pads from their carrier backing

and place at the four corners of the bottom of the

unit.

Power Connections

The preferred method of powering a VIP-821 is

via a power over Ethernet switch meeting the

802.3af specification.

If the rear panel barrel connector is used for

power, the preferred power supply is a Valcom

VIP-324D.

Make all required signal connections before

applying power to the unit. If powering via

802.3af, make sure all signal connections via the

rear panel are made then connect the VIP-821 to

the Ethernet switch.

If power is supplied via the barrel connector,

make sure all signal connections are secure.

Attach the unit to the network via the front panel

RJ-45 Ethernet connector. Apply power by

plugging the power supply in to the VIP-821 via

the barrel connector on the rear of the VIP-821.

Network Connection

The VIP-821 has one RJ-45 network connector

on the front panel.

Use a standard Ethernet patch cable to connect

the VIP-821 to an Ethernet switch. If the Ethernet

switch is 802.3af compliant the VIP-821 will draw

power from it.

Signal Connections

On the rear panel, the VIP-821 has 1 RJ-11 jack

for connection to a FXS circuit. 1 RJ-11 jack for a

failover telephone connection.

FXO Connection: Connect standard analog FXS

circuit to the VIP-821 via the rear panel RJ-11

jack labeled Line. Tip and Ring appear on pins 3

and 4 of these jacks.

Failover Connection: Connect a standard

analog telephone to the VIP-821 via the rear

panel RJ-11 jack labeled Phone. Tip and Ring

appear on pins 3 and 4 of these jacks. In the

case of a device failure, the telephone will be

able to access the FXS circuit or single line port.

REAR VIEW

Status Indicator Lights

The VIP-821 has 3 status indication lights on the

front panel.

STATUS: Flashes then illuminates to indicate

power.

Produkt Specifikationer

Mærke:	Valcom
Kategori:	Netværkskort/adapter
Model:	Trunk Port VIP-821
Bredde:	156 mm
Dybde:	133.3 mm
Højde:	35 mm
Vægt:	562.5 g
Wi-Fi:	Ingen
Relativ luftfugtighed ved drift (H-H):	0 - 85 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 40 °C
Strømforsyningstype:	24 VDC
Forbindelsesteknologi:	Ledningsført
Netværksstandarder:	IEEE 802.3af
Understøttede netværksprotokoller:	DHCP, IGMP v3, UDP, TCP, HTTP, Telnet, FTP
LED-indikatorer:	Ja
Udgangsspænding:	24 V
Værtsgrænseflade:	RJ-45
Grænseflade:	Ethernet
Intern:	Ingen
Maksimal dataoverførselshastighed:	100 Mbit/s
Strøm-LED:	Ja
Indgangsstrøm:	0.325 A
Netværk klar:	Ja
Link/Act LED:	Ja