Valcom VIP-812 Manual

Valcom Netværkskort/adapter VIP-812

Læs gratis den danske manual til Valcom VIP-812 (5 sider) i kategorien Netværkskort/adapter. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Valcom VIP-812, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

1 947996

ISSUE 5

VIP-812

DUAL NETWORKED STATION PORT

INTRODUCTION

The VIP-812 Dual Networked Station Port allows

most loop start terminal devices to be connected

to a managed IP-based LAN/WAN.

SPECIFICATIONS

Access Methods

 PBX, FXO Port

 POTS telephone set

Features

 RJ-45 for network connection

 2 RJ-11 telephone connections

 4 Relays with Form C contacts

 Front panel activity LED

 Network activity LEDs

 2 RENS

 2.5mm jack for external power

 Power over Ethernet (PoE) 802.3af

compatible

Dimensions/Weight

 1.75 H x 6.75" W x 9.5" D

(4.45cm H x 17.15cm W x 24.13cm D)

 Weight: 1.75 lbs. (0.80 kg)

Nominal Specifications

Input Impedance: 600 Ohms

Input Level: -10dBm

Output Impedance: 600 Ohms

Output Level: - 10dBm nominal

Relay Current: 1 AMP @ 24VDC

Nominal Power Requirements

Via rear panel barrel connector:

Voltage: 24VDC

Current: 325mA

Via 802.3af (PoE) Ethernet Switch:

802.3af: Class 3

Environment

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

Packing List

Qty Item

1 VIP-812

1 VSP Document

2 Mounting Brackets W/ Hardware

4 Rubber Pads

INSTALLATION

NOTE: The telephone system referred to in

this manual is the customer premise

equipment such as an electronic key system,

a PBX or a dedicated single line telephone

sets. The VIP-812 is not intended for direct or

indirect connection to the public telephone

network. When used with a customer premise

telephone system such as a key system or

PBX system, these units are interfaced to the

system via a fully protected page port or

system central office port, which is a fully

protected interface device. Also, the host

system must be configured to disallow central

office trunk conferencing in order to prevent

indirect connection to the public network.

2 947996

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

Precautionary Designations

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses and can radiate

radio frequency energy and if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference in which case the user

will be required to correct the interference at

his own expense.

Mounting

The VIP-812 is designed for wall, table or rack

mounting.

Table: Provided with the VIP-812 are four rubber

pads. Peel pads from their carrier backing and

place at the four corners of the bottom of the unit.

Wall: Using the template on last page of this

document, mark the location of the bracket screw

holes on the wall. Drill 5/64" pilot holes, 3/4"

deep, at each screw location and use the wood

screws provided to attach the brackets to the

wall. For surfaces other than wood, use

hardware appropriate for the surface (not

included). With the brackets securely attached to

the wall, attach the VIP-812 to the brackets using

the included hardware. Figure 2 illustrates the

bracket assembly.

Rack: Following the assembly drawing, attach

the two mounting brackets to the VIP-812 unit.

Using rack screws, mount the VIP-812 in an

available 1U rack slot. See Figure 1.

Figure 1. Rack Mount

Figure 2. Wall Mount

Power Connections

The preferred method of powering a VIP-812 is

via a Power over Ethernet (PoE) switch meeting

the 802.3af specification.

If the rear panel barrel connector is used for

power, the preferred power supply is a Valcom

VIP-324D.

Make all required signal connections before

applying power to the unit. If powering via

802.3af, make sure all signal connections via the

back panel are made then connect the VIP-812 to

the Ethernet switch.

If power is supplied via the barrel connector,

make sure all signal connections are secure.

Attach the unit to the network via the front panel

RJ-45 Ethernet connector. Apply power by

plugging the power supply in to the VIP-812 via

the barrel connector on the rear of the VIP-812.

Produkt Specifikationer

Mærke:	Valcom
Kategori:	Netværkskort/adapter
Model:	VIP-812
Bredde:	171.5 mm
Dybde:	241 mm
Højde:	44.5 mm
Vægt:	790 g
Wi-Fi:	Ingen
Relativ luftfugtighed ved drift (H-H):	0 - 85 %
Ethernet LAN-porte (RJ-45):	1
Ethernet LAN:	Ja
Driftstemperatur (T-T):	0 - 40 °C
Forbindelsesteknologi:	Ledningsført
Netværksstandarder:	IEEE 802.3af
Understøttede netværksprotokoller:	DHCP, IGMP v3, UDP, TCP, HTTP, Telnet, FTP
LED-indikatorer:	Ja
Værtsgrænseflade:	RJ-45
Grænseflade:	Ethernet
Intern:	Ingen
Maksimal dataoverførselshastighed:	100 Mbit/s
Stik:	2 x RJ-11
USB-drevet:	Ingen
Netværk klar:	Ja
Link/Act LED:	Ja