Valcom VIP-9890-CB Manual

Valcom Intercomsystem VIP-9890-CB

Læs gratis den danske manual til Valcom VIP-9890-CB (4 sider) i kategorien Intercomsystem. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Valcom VIP-9890-CB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

1 947704

ISSUE 3

VIP-9890-CB

Vandal Resistant IP DoorPhone/Intercom

INTRODUCTION

The VIP-9890-CB IP Talkback Doorphone /

Intercom allows communication to Valcom

FXS units (VIP-811, -812, -814) and SIP-enabled

telephone systems via an IP network. The

VIP-9890-CB combines a rugged; weather-

resistant talkback paging horn with a vandal-

resistant enclosure, which is ideally suited for

high-noise, exposed environments.

SPECIFICATIONS

Access Methods

 PBX, FXO Port w/VIP-811

 POTS telephone set w/VIP-811

 Valcom M Cast Page Group

 SIP – enabled telephone system

Features

 RJ-45 for network connection

 1 Form C contact

 LED Status Indicator

 Network activity LEDs

 Power over Ethernet (PoE) 802.3af

compatible

 Door Opening Contact Provided

Dimensions/Weight

Intercom Unit:

 10.0” H x 12.5" W x 4" D

(25.4cm H x 31.75cm W x 10.2cm D)

 Weight: 10.75lbs. (4.1 kg)

Network Interface:

 2.0” H x 4.63" W x 9.13" D

(5.1cm H x 11.8cm W x 23.2cm D)

 Weight: 0.80lbs. (0.36 kg)

Nominal Specifications

Input Impedance: 600 Ohms

Input Level: -10dBm

Output Impedance: 600 Ohms

Output Level: -10dBm nominal

Relay Current: 1AMP @ 24VDC

Nominal Power Requirements

Via 802.3af (PoE) Ethernet Switch Class 3

Environment

VIP-9890-CB Network Interface

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

VIP-9890-CB Intercom Unit:

Suitable for indoor or outdoor installation

Packing List

Qty Item

1 VIP-9890-CB Network Interface

1 VIP-9890-CB Intercom Unit

1 VSP Document

4 Tamper Hardware (Intercom unit only)

1 VIP172-RLY Relay Block

4 Wood Screws

2 947704

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

Precautionary Designations

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses and can radiate

radio frequency energy and if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference in which case the user

will be required to correct the interference at

his own expense.

INSTALLATION

Operation:

The VIP-9890-CB provides intercom access via

network connection to customer telephone

system or stand alone telephone set. Interface to

customer telephone system can be via SIP

registration to a Voice over IP (VoIP) telephone

system, or FXO port (when used with a VIP-811).

Pressing the call button on the intercom unit

initiates a call to a user-specified telephone

number, and the call assurance LED behind the

intercom unit face plate begins to flash. When

the call is answered, a hands-free

communications path is established to the

intercom unit, and the call assurance LED behind

the face plate remains lit. The form C relay

included with the VIP-9890-CB may be activated

by pressing the # key on the answering

telephone, with the relay typically being used to

activate door entry equipment.

Mounting

For enhanced protection against static

electrical discharge, it is recommended the

intercom unit shipped with the VIP-9890-CB

be installed onto a grounded electrical box, If

surface mounted, ground box to local ground.

The VIP-9890-CB Intercom unit is designed for

double gang FD electrical box mounting and must

be within 300 meters of the VIP-9890-CB

Network Interface. See NEMA OS 3-2002

sec.1.2.3.5 for FD box speciﬁcations.

The VIP-9890-CB Network Interface is designed

for wall mounting and must be within 100 meters

of the network switch. Using the wood screws

provided, secure the VIP-9890-CB Network

Interface to the wall. Remove the Intercom unit

from the packing container. Using a Phillips

screwdriver, remove the two screws securing the

front grille to the enclosure. Pre-drilled 13/64”

mounting holes in the back of the enclosure are

designed to fit a single gang, double gang or

octagon outlet box. If not attaching to an outlet

box, use the enclosure as a template. Hold the

enclosure in the desired position on the wall and

mark the location of mounting holes. Depending

on wall construction type, prepare the mounting

hole locations on the wall to securely attach the

enclosure.

Wiring may be inserted through the large hole in

the back of the enclosure, or through the

knockout hole in the top of the enclosure. Insert

wiring for signal connections and relay

connections (if used) through desired hole. Use

mounting hardware (not included) appropriate for

the wall type to securely mount the enclosure to

the wall.

After making signal connections, align the

grille/speaker assembly with the enclosure.

Install the four supplied tamper-resistant screws

through the grille into the enclosure. Use a 1/8”

security hex bit (not included) to tighten the

screws securely.

Power Connections

The only method of powering a VIP-9890-CB

Network Interface is via a Power over Ethernet

(PoE) switch or power injector meeting the

802.3af specification.

Make all required signal connections before

connecting to Ethernet switch or power injector

meeting the 802.3af specification.

Produkt Specifikationer

Mærke:	Valcom
Kategori:	Intercomsystem
Model:	VIP-9890-CB

Har du brug for hjælp?

Hvis du har brug for hjælp til Valcom VIP-9890-CB stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Intercomsystem Valcom Manualer

Valcom V-1072B Manual

6 September 2024

6 September 2024

6 September 2024

6 September 2024

6 September 2024

Valcom V-5324004 Manual

6 September 2024

Valcom V-9908 Manual

6 September 2024

Valcom V-9923B Manual

6 September 2024

Valcom V-1096 Manual

6 September 2024

Valcom MultiPath Talkback Manual

6 September 2024

Intercomsystem Manualer

Nyeste Intercomsystem Manualer

Viking E-40-SS-EWP Manual

28 Marts 2025

Viking E-1600-40-IPEWP Manual

27 Marts 2025

Hikvision DS-KH2230T Manual

27 Marts 2025

Viking E-1600-20A-EWP Manual

27 Marts 2025

Louroe Electronics AOP-SP-PB Manual

10 Marts 2025

2N Telecommunications 9151104 Manual

20 Februar 2025

2N Telecommunications Indoor Compact Manual

20 Februar 2025

Axis TI8202 Manual

20 Februar 2025

Axis TI8904 Manual

20 Februar 2025

Rollei Xtalk Manual

5 Februar 2025