Vemer Sensor LED Manual

Vemer Bevægelsesdetektor Sensor LED

Læs gratis den danske manual til Vemer Sensor LED (1 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Vemer Sensor LED, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

User manual

Movement detectors with LED headlight

Read all instructions carefully

The

Sensor LED

and

Sensor 2LED

proximity switches and are electronic switching devices

containing micro-disconnection (μ) according to EN 60669-2-1. They have an LED headlight

(single for Sensor LED, double for Sensor 2LED) that is activated when a heat source moves in

front of the device and is deactivated when no movement is intercepted, after a settable period

of elapsed time. They also have a relay for the connection of an external device (an auxiliary

headlight, an audible alarm, ...) which is activated simultaneously with the headlight.

SAFETY WARNINGS

During installation and operation of the device, comply with the following instructions:

1) The device must be installed by a skilled person, in strict compliance with the

connection diagrams

2) Do not power on or connect the device if any part of it is damaged

3) In the building where the device is to be installed, there must be a switch and a

device for protection from overloads

4) Before touching the connector terminals make sure that the wires to be connected

are not live.

Code Model Description

VE767200 Sensor LED Movement detector 200° with LED headlight 13W

VE767300 Sensor 2LED Movement detector 200° with 2 LED headlights 2x13W

TECHNICAL CHARACTERISTICS

• Power supply: 230V AC 50Hz

• Type of LED headlight:

- Sensor LED: 1x13W, 1000 lm

- Sensor 2LED: 2x13W, 2000 lm

- Colour temperature: 4000K

• Relay with breaking capacity of 10A / 250V AC (on resistive load)

• Maximum cables section: 2 x 1.5 mm2

• Range of brightness: 5-1000 lux

• Intervention time: from 3 seconds to 30 minutes (approximate)

• Angle of detection: 200°

• Range of detection: − frontal 12m at 20°C

− lateral 8m at 20°C

• Operating temperature: -20 °C ÷ +40 °C

• Protection degree: IP55

• Insulation: class II

INSTALLATION

• The device must be installed far from inductive loads (motors, transformers, telephone

antennas, transformer plants, industrial machinery, etc.) as especially strong magnetic

elds may alter operation. The device must also be protected from sunlight. It must not

be placed near lights, near devices that are subject to temperature changes (heating, air

conditioning). It must be located far from highly reective surfaces.

Remove the cover by loosening the screw at the bottom. Fasten the base cover at the point

on the wall where you want to install it, at a height of 2-3 metres.

The direction of movement of the heat source must be transversal to lens of the device,

because detection occurs by means of intersection of bands. Therefore, if source moves

parallel to the bands, detection will occur at a lesser distance. The ambient temperature

also affects the sensitivity of the device. The higher the temperature, the poorer sensitivity

will be.

• The head can rotate horizontally of about 180° and vertically of about 45°. To adjust the

eld of detection:

− turn the intervention time selector to the minimum and the brightness selector to ( );

− check coverage by moving inside the eld of detection.

The device is also equipped with limiters of the detection area which, if applied to the lens,

make it possible to exclude one or more sectors of the eld of detection.

• To adjust the brightness, turn the selector towards ( ); when the ambient brightness

is as desired for operation, start turning the selector the other way, until illumination

occurs.

• To adjust the intervention time, turn the selector ( ) to the desired position. You can

choose from a minimum of 3 seconds to a maximum of 30 minutes. This time is reset

each time there is an interception by the detector.

GREATER SENSITIVITY

direction of

movement

direction of

movement

LESS SENSITIVITY

OPERATION

• At start and after each restoring of the power supply after a blackout, the sensor activates

the LED headlight and the load connected for 30 seconds, regardless of the brightness

level and the actual presence of movement in the eld of detection.

• During normal operation, when the level of brightness drops below the set level, the

device sets up for detection, and signals this condition via ashing of the internal LED.

REFERENCE STANDARDS

Conformity to the EU directives:

2014/35/EU (LDV)

2014/30/EU (EMCD)

is declared with reference to harmonized standard:

EN 60598-1/EN 60598-2-1

Incandescent

Non-compensated fluorescent

Compensated fluorescent

Halogen (230V)

LED

Low consumption lamp (CFL)

1000 W

500 VA

150 VA

1000 W

125 VA

250 VA

Dimensions

Sensor LED

Sensor 2LED

100

135

150

185

175

205

155

170

175

190

L P1

Wall-mounting

Connection diagrams

L' N L

230 V AC

LAMPADA

L' N L

Mod. Sensor LED

Sensor 2LED

ISCOM058-2106

ADDITIONAL

LAMP

information to users pursuant to art. 14 of the directive

2012/19 / EU of the european parliament and of the council

of 4 july 2012 on waste electrical and electronic equipment (WEEE)

If the crossed-out bin symbol appears on the equipment or packaging,

this means the product must not be included with other general

waste at the end of its working life.

The user must take the worn product to a sorted waste center,

or return it to the retailer when purchasing a new one.

Products for disposal can be consigned free of charge (without any new purchase obligation)

to retailers with a sales area of at least 400 m

2, if they measure less than 25 cm.

An efﬁcient sorted waste collection for the environmentally friendly disposal of the used device,

or its subsequent recycling, helps avoid the potential negative effects on the environment

and people’s health, and encourages the re-use and/or

recycling of the construction materials.

Produkt Specifikationer

Mærke:	Vemer
Kategori:	Bevægelsesdetektor
Model:	Sensor LED

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer Sensor LED stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Vemer Manualer

Vemer Muvy DUO Manual

4 August 2025

Vemer Sensor 2LED Manual

28 Juli 2024

Vemer Sensor LED Manual

27 Juli 2024

Vemer Sensor 140 Manual

28 Oktober 2023

Vemer Sensor 200 Manual

19 September 2023

Vemer Sensor 140 Blister Manual

31 August 2023

Vemer Sensor HF Manual

1 Februar 2023

Vemer Sensor-360 Manual

23 December 2022

Vemer Sensor-2T Manual

4 November 2022

Vemer Sensor-T Manual

14 Oktober 2022

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Optex AX-200TF Manual

10 August 2025

10 August 2025

10 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

Theben thePassa P360 KNX UP Manual

3 August 2025

Theben theRonda P360 DALI-2 HCL UP Manual

3 August 2025

Theben thePiccola S360-100 DE Manual

3 August 2025