Vemer Sensor 200 Manual

Vemer Bevægelsesdetektor Sensor 200

Læs gratis den danske manual til Vemer Sensor 200 (1 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Vemer Sensor 200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

User manual

Movement detectors

Read all instructions carefully

The

Sensor 140

and

Sensor 200

proximity switches are electronic switching devices

containing micro-disconnection (µ) according to EN 60669-2-1. The output circuit is activated

when a heat source moves in front of the device and is deactivated when no movement is

intercepted, after a settable period of elapsed time.

SAFETY WARNINGS

During installation and operation of the device, comply with the following instructions:

1) The device must be installed by a qualied person, in strict compliance with the

connection diagrams

2) Do not power on or connect the device if any part of it is damaged

3) In the building where the device is to be installed, there must be a switch and a

device for protection from overloads

4) Before touching the connector terminals make sure that the wires to be connected

are not live.

Code Model Description

VE212700 Sensor 140 Movement detector 140° - White

VE213500 Sensor 200 Movement detector 200° - White

VE787700 Sensor 200 Nero Movement detector 200° - Black

TECHNICAL CHARACTERISTICS

• Power supply: 230V AC 50Hz

• Beaking capacity: 5A 250V AC (resistive load)

• Maximum recommended loads:

− Incandescent light bulbs: 1000W

− Non-compensated uorescent: 500W

− Compensated uorescent: 250W

− Halogen (230V AC): 1000W

− Low consumption bulbs: 200W

• Consumption: 6VA (1W)

• Range of brightness: 5-30-2000 lux

• Intervention time: from 3 seconds to 30 minutes (approximate)

• Angle of detection: − Sensor 140: 140°

− Sensor 200: 200°

• Range of detection: − frontal 12m at 20°C

− lateral 8m at 20°C

• Operating temperature: -20 °C ÷ +40 °C

• Protection degree: IP55

• Insulation: class II

INSTALLATION

• The device must be installed far from inductive loads (motors, transformers, telephone

antennas, transformer plants, industrial machinery, etc.) as especially strong magnetic

elds may alter operation. The device must also be protected from sunlight. It must not

be placed near lights, near devices that are subject to temperature changes (heating, air

conditioning). It must be located far from highly reective surfaces.

Remove the cover by loosening the screw at the bottom. Fasten the base cover at the point

on the wall where you want to install it, at a height of 2-3 metres.

The direction of movement of the heat source must be transversal to lens of the device,

because detection occurs by means of intersection of bands. Therefore, if source moves

parallel to the bands, detection will occur at a lesser distance. The ambient temperature

also affects the sensitivity of the device. The higher the temperature, the poorer sensitivity

will be.

• The head can rotate horizontally about 180° and vertically about 45°.

• To adjust the eld of detection:

− turn the intervention time selector to the minimum and the brightness selector to ();

− check coverage by moving inside the eld of detection.

The device is also equipped with limiters of the detection area divided into four sectors. If

applied to the lens, they make it possible to exclude one or more of the sectors of the eld

of detection.

• To adjust the brightness, turn the selector towards ( ); when the ambient brightness is as 

desired for operation, start turning the selector the other way, until illumination occurs.

• To adjust the intervention time, turn the selector ( ) to the desired position. You can 

choose from a minimum of 3 seconds to a maximum of 30 minutes. This time is reset

each time there is an interception by the detector.

OPERATION

• At start and after each restoring of the power supply after a blackout, the sensor activates

the loads connected for 30 seconds, regardless of the brightness level and the actual

presence of movement in the eld of detection.

• During normal operation, when the level of brightness drops below the set level, the

device sets up for detection, and signals this condition via ashing of the internal LED.

REFERENCE STANDARDS

Conformity to the EU directives:

2014/35/EU (LDV)

2014/30/EU (EMCD)

is declared with reference to harmonized standard:

EN 60669-2-1

Dimensions

10072

Connection diagrams

L' N L

230 V ACLAMPADINA

BULB

Sensitivity

GREATER SENSITIVITY LESS SENSITIVITY

direction of

movement

direction of

movement

Field of detection

information to users pursuant to art. 14 of the directive

2012/19 / EU of the european parliament and of the council

of 4 july 2012 on waste electrical and electronic equipment (WEEE)

If the crossed-out bin symbol appears on the equipment or packaging,

this means the product must not be included with other general

waste at the end of its working life.

The user must take the worn product to a sorted waste center,

or return it to the retailer when purchasing a new one.

Products for disposal can be consigned free of charge (without any new purchase obligation)

to retailers with a sales area of at least 400 m

2, if they measure less than 25 cm.

An efﬁcient sorted waste collection for the environmentally friendly disposal of the used device,

or its subsequent recycling, helps avoid the potential negative effects on the environment

and people’s health, and encourages the re-use and/or

recycling of the construction materials.

ISCOM017-2106

Mod. Sensor 140

Sensor 200

Produkt Specifikationer

Mærke:	Vemer
Kategori:	Bevægelsesdetektor
Model:	Sensor 200

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer Sensor 200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Vemer Manualer

Vemer Muvy DUO Manual

4 August 2025

Vemer Sensor 2LED Manual

28 Juli 2024

Vemer Sensor LED Manual

27 Juli 2024

Vemer Sensor 140 Manual

28 Oktober 2023

Vemer Sensor 200 Manual

19 September 2023

Vemer Sensor 140 Blister Manual

31 August 2023

Vemer Sensor HF Manual

1 Februar 2023

Vemer Sensor-360 Manual

23 December 2022

Vemer Sensor-2T Manual

4 November 2022

Vemer Sensor-T Manual

14 Oktober 2022

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Abus Smartvest Pro FUBW45000 Manual

29 Oktober 2025

Axis D2110-VE Manual

12 Oktober 2025

Homematic IP HmIP-SPDR Manual

29 September 2025

Brinno MAS100 Manual

28 September 2025

Crestron CEN-ODT-C-POE Manual

24 September 2025

Crestron ZUMLINK-US-HALLWAY-DLS-RLY Manual

24 September 2025

Crestron ZUMLINK-US-HALLWAY-DLS Manual

24 September 2025

Crestron ZUMLINK-US-ONEWAY-DLS Manual

23 September 2025

Crestron ZUMLINK-IR-QUATTRO-DLS-RLY Manual

23 September 2025

Crestron ZUMLINK-IR-QUATTRO-HD-DLS-RLY Manual

23 September 2025