Vemer Sensor-360 Manual

Vemer Bevægelsesdetektor Sensor-360

Læs gratis den danske manual til Vemer Sensor-360 (1 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 56 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 28.5 anmeldelser. Har du et spørgsmål om Vemer Sensor-360, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

User manual

Movement detector

Read all instructions carefully

The

Sensor-360

proximity switch is electronic switching device containing

micro-disconnection (μ) according to EN 60669-2-1. The output circuit is activated when a

heat source moves in front of the device and is deactivated when no movement is intercepted,

after a settable period of elapsed time.

SAFETY WARNINGS

During installation and operation of the instrument, comply with the following

instructions:

1) The instrument must be installed by a skilled person, in strict compliance with the

connection diagrams

2) Do not power on or connect the instrument if any part of it is damaged

3) In the building where the instrument is to be installed, there must be a switch and a

device for protection from overloads

4) Before touching the connector terminals make sure that the wires to be connected or

already connected to the instrument are not live.

Code Model Description

VP403000 Sensor-360 Movement detector 360°

TECHNICAL CHARACTERISTICS

• Power supply: 230V AC 50Hz

• Breaking capacity: 10A 250V AC (resistive load)

• Maximum recommended loads:

− Incandescent light bulbs: 1000W

− Non-compensated uorescent: 500W

− Compensated uorescent: 250W

− Halogen (230V AC): 1000W

− Low consumption bulbs: 200W

• Consumption: < 2W

• Range of brightness: 3-300- lux∞

• Time range: from 3 seconds to 10 minutes (approximate)

• Detection angle: 360°

• Maximum detection height: 5 m

• Operating temperature: -20 °C ÷ +40 °C

• Protection degree: IP20

• Insulation: class II

INSTALLATION

• The device must be installed far from inductive loads (motors, transformers, telephone

antennas, transformer plants, industrial machinery, etc.) as especially strong magnetic

elds may alter operation. The device must also be protected from rain and sunlight.

It must not be placed near lights, near devices that are subject to temperature changes

(heating, air conditioning). It must be located far from highly reective surfaces.

• The detection area directly depends on the installation height. In particular, an

installation at 2.5 meters height, permits to detection a eld of 3.5 meters ray.

• The sensibility is instead inuenced by the environment temperature (the higher

the temperature, the worse the sensitivity because the unit operates by detecting the

movement of a heat source) and by the direction of the movement.

GREATER SENSITIVITY

direction of

movement

direction of

movement

LESS SENSITIVITY

OPERATION

• To install the instrument, remove the cover and set the selectors.

• To set the detection eld:

− rotate the “lux” selector to the “ ” position and the “time” selector to the “ ” position;

− check coverage by moving within the detection eld limits.

The device permits to limit the eld of the detection area. To exclude one or more sectors,

applied a piece of insulating tape on the relative part of the sensor.

• The Sensor-360 proximity switch can be adjusted to that it only operates when the

lighting conditions are below the selected level. By turning the “lux” selector to the “ ”

position, it will react under any luminosity conditions. By turning it to the “ ” position, it

will only react under low luminosity conditions.

• The “time” selector permits to set the switch-on delay.

It’s possible to choice from 3 seconds “ ” to 10 minutes “ ”.

REFERENCE STANDARDS

Conformity to the EU directives:

2014/35/UE (LDV), 2014/30/UE (EMCD)

is declared with reference to harmonized standard: EN 60669-2-1

Mod. Sensor-360

information to users pursuant to art. 14 of the directive

2012/19 / EU of the european parliament and of the council

of 4 july 2012 on waste electrical and electronic equipment (WEEE)

If the crossed-out bin symbol appears on the equipment or packaging,

this means the product must not be included with other general

waste at the end of its working life.

The user must take the worn product to a sorted waste center,

or return it to the retailer when purchasing a new one.

Products for disposal can be consigned free of charge (without any new purchase obligation)

to retailers with a sales area of at least 400 m

2, if they measure less than 25 cm.

An efﬁcient sorted waste collection for the environmentally friendly disposal of the used device,

or its subsequent recycling, helps avoid the potential negative effects on the environment

and people’s health, and encourages the re-use and/or

recycling of the construction materials.

Dimensions

46138.5

Connection diagrams

L N

Operation

SELECTORS

CENTRING INDEX

SENSOR

Produkt Specifikationer

Mærke:	Vemer
Kategori:	Bevægelsesdetektor
Model:	Sensor-360

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer Sensor-360 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Vemer Manualer

Vemer Muvy DUO Manual

4 August 2025

Vemer Sensor 2LED Manual

28 Juli 2024

Vemer Sensor LED Manual

27 Juli 2024

Vemer Sensor 140 Manual

28 Oktober 2023

Vemer Sensor 200 Manual

19 September 2023

Vemer Sensor 140 Blister Manual

31 August 2023

Vemer Sensor HF Manual

1 Februar 2023

Vemer Sensor-360 Manual

23 December 2022

Vemer Sensor-2T Manual

4 November 2022

Vemer Sensor-T Manual

14 Oktober 2022

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Crestron GLA-LDL-PC-0-10-WL Manual

9 September 2025

Biltema 46-2010 Manual

3 September 2025

Biltema 46-2009 Manual

2 September 2025

Leviton OSD10-I0I Manual

30 August 2025

Leviton OSC04-I0W Manual

30 August 2025

Leviton OSC05-M0W Manual

29 August 2025

Leviton OSC10-M0W Manual

29 August 2025

Leviton OSC20-M0W Manual

29 August 2025

Leviton OSC04-IAW Manual

29 August 2025

Leviton OSC20-RMW Manual

29 August 2025