Vemer Sensor HF Manual

Vemer Bevægelsesdetektor Sensor HF

Læs gratis den danske manual til Vemer Sensor HF (1 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Vemer Sensor HF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

User manual

Movement detectors

Read all instructions carefully

The Sensor HF proximity switch is electronic switching device containing

micro-disconnection (μ) according to EN 60669-2-1, that emits superhigh frequency (5.8 GHz)

electromagnetic waves and captures their echoes. Any changes in the echoes are detected by

the sensor indicating the presence or persons or animals and a microprocessor controls the

connected lights or application. This device detects within a radius of action of between 0.5 and

6 metres, with a 270º coverage.

SAFETY WARNINGS

During installation and operation of the instrument, comply with the following

instructions:

1) The instrument must be installed by a skilled person, in strict compliance with the

connection diagrams

2) Do not power on or connect the instrument if any part of it is damaged

3) In the building where the instrument is to be installed, there must be a switch and a

device for protection from overloads

4) Before touching the connector terminals make sure that the wires to be connected or

already connected to the instrument are not live.

Code Model Description

VE214300 Sensor-HF Movement detector wall-mounted

TECHNICAL CHARACTERISTICS

• Power supply: 230V AC 50Hz

• Sensor: 5.8 GHz

• Breaking capacity: 6A 250V AC (resistive load)

• Maximum recommended loads:

− Incandescent lamps: 1,000W

− Uncompensated uorescents: 500 W

− Compensated uorescents: 250 W

− Halogens (230V AC): 1,000 W

− Low-consumption lamps: 200 VA

• Own consumption: 11 VA (1.7 W)

• Capture angle: 270º

• Detection range: from 0.5 to 6 metres front and up to 3 metres to the side,

installed at a height of 1.7 metres

• Luminosity range: from 0.5 to 2,000 Lux

• Timing range: from 3 seconds to 30 minutes

• Operating temperature: 0ºC ÷ +50ºC

• Protection degree: IP20

• Insulation: class II

INSTALLATION

• The device must be installed far from inductive loads (motors, transformers, telephone

antennas, transformer plants, industrial machinery, etc.) as especially strong magnetic

elds may alter operation. The device must also be protected from rain and sunlight.

It must not be placed near lights, near devices that are subject to temperature changes

(heating, air conditioning). It must be located far from highly reective surfaces.

• It is wall-mounted using the included at bracket, wall-plugs and screws (a special bracket

is included for corner installation). The ideal sensor wall-installation height is between 0.3

and 2.4 metres. Once the bracket is secured to the wall in the desired location, the Sensor

HF should be slid into position along the slide until it is fully secured.

• Remove the cover with a slight rotation forwards and loosen the securing screw for the

connections cover for access to the terminal block.

Pass the connection wires through the cavity in the lower part of the unit, or through the

wiring access marked on the base.

It must be connected in accordance with the connection diagram. Once connected, close

the cover again and tighten the screw.

OPERATION

• The Sensor HF has three potentiometers behind the front cover:

 TIME permits to set the time in which the load is on. Timing commences after

detecting the last movement (adjustable from three seconds to thirty minutes).

® RANGE permits to set the detecting range of the device (adjustable from 0,5 meter and

6 meters).

  permits to adjust the brightness under the device is on (adjustable from 0,5 lux

to 2000 lux).

• Ten seconds after the unit is switched on the sensor enters AUTO mode. Turn the “time”

to minimum (-) and the “lux” potentiometer to ( ). Move in front of the sensor until the 

connected device lights come on. This provides an idea of the detection eld range.

Set the “time” and “lux” potentiometers to the desired positions.

• It is possible to achieve permanent switch-on, during four hours, rapid switching on

and off twice (less than two seconds). A return to auto mode can be made in permanent

switch-on by switching off for more than two seconds.

The ledwill ash three times when the unit passes to auto mode. If the led remains

permanently on, the sensor is in permanent mode.

REFERENCE STANDARDS

Conformity to the EU directives:

2014/35/UE (LDV)

2014/30/UE (EMCD)

is declared with reference to harmonized standard:

EN 60669-2-1

ISCOM020-2106

Mod. Sensor-HF

Dimensions

Installation

78 46

116

Connection diagram

L N

N L

NL1

Push the connector with

a screwdriver to open

and insert wire

- Stiff wire between

0.75 and 2 mm2.

- The lenght of insulation to

remove should be 7 mm.

7 mm.

information to users pursuant to art. 14 of the directive

2012/19 / EU of the european parliament and of the council

of 4 july 2012 on waste electrical and electronic equipment (WEEE)

If the crossed-out bin symbol appears on the equipment or packaging,

this means the product must not be included with other general

waste at the end of its working life.

The user must take the worn product to a sorted waste center,

or return it to the retailer when purchasing a new one.

Products for disposal can be consigned free of charge (without any new purchase obligation)

to retailers with a sales area of at least 400 m

2, if they measure less than 25 cm.

An efﬁcient sorted waste collection for the environmentally friendly disposal of the used device,

or its subsequent recycling, helps avoid the potential negative effects on the environment

and people’s health, and encourages the re-use and/or

recycling of the construction materials.

Produkt Specifikationer

Mærke:	Vemer
Kategori:	Bevægelsesdetektor
Model:	Sensor HF

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer Sensor HF stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Vemer Manualer

Vemer Muvy DUO Manual

4 August 2025

Vemer Sensor 2LED Manual

28 Juli 2024

Vemer Sensor LED Manual

27 Juli 2024

Vemer Sensor 140 Manual

28 Oktober 2023

Vemer Sensor 200 Manual

19 September 2023

Vemer Sensor 140 Blister Manual

31 August 2023

Vemer Sensor HF Manual

1 Februar 2023

Vemer Sensor-360 Manual

23 December 2022

Vemer Sensor-2T Manual

4 November 2022

Vemer Sensor-T Manual

14 Oktober 2022

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Crestron GLA-LDL-PC-0-10-WL Manual

9 September 2025

Biltema 46-2010 Manual

3 September 2025

Biltema 46-2009 Manual

2 September 2025

Leviton OSD10-I0I Manual

30 August 2025

Leviton OSC04-I0W Manual

30 August 2025

Leviton OSC05-M0W Manual

29 August 2025

Leviton OSC10-M0W Manual

29 August 2025

Leviton OSC20-M0W Manual

29 August 2025

Leviton OSC04-IAW Manual

29 August 2025

Leviton OSC20-RMW Manual

29 August 2025