Vemer SOLAR-1 Micro Manual

Vemer Ikke kategoriseret SOLAR-1 Micro

Læs gratis den danske manual til Vemer SOLAR-1 Micro (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Vemer SOLAR-1 Micro, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1 3 INSTALLATION

User Manual

LOADS CONTROL 1 RELAY FOR ENERGY PRODUCTION

Read all the instructions carefully

Not

insertable

load

Insertable

load

Electronic instrument for controlling the self-produced active power of

your photovoltaic system. If the power entered on the network (surplus of

power, that is to say produced power – consumed power) is higher than

a set threshold (setpoint) for a settable period of time (Ton), the SOLAR-1

Micro switches on the load connected to the relay, in order to maximize the

selfconsumption of the power produced.

Code Model Descrizione

VE793900 SOLAR-1 Micro Loads control for systems of energy production 1 relay

SAFETY WARNINGS

During the installation and the operation of the instrument it’s necessary

to observe the following instructions:

1) The instrument must be installed by a qualified person by observing

scrupulously the connection diagrams.

2) The instrument must be installed and activated in compliance with current

electric systems standards.

3) After installation, inaccessibility to the connection terminals without

appropriate tools must be granted.

4) Do not use the instrument for other purposes different from the one

specified.

5) The instrument must be installed in a closed electrical panel adequately

protected.

6) In the power supply network a bipolar disconnection must be present.

7) A protection device against over-currents should be installed in the

electrical system, upstream of the device.

8) Before accessing the connection terminals, verify that the leads are not live.

9) Do not power on or connect the instrument if any part of it is damaged.

10) The instrument can be used in environments with overvoltage category III

and pollution degree 2, according to the CEI EN 61010-1 standard.

TECHNICAL CHARACTERISTICS

• Power supply: 230 Vac (-15% ÷ +10%) 50/60 Hz

• Maximum own consumption: 8 VA

• Voltage input consumption: < 2.5 VA

• Current input consumption: < 2.5 VA

• Measurement precision: 1% of active power

• Maximum diameter of the conductor through the TA: 10 mm

• Current connection until 65 A through current transformer

• Settable setpoint range: 1 ÷ 8 kW

• Settable hysteresis range: 0 ÷ 8 kW

• Time range Ton: 30 s ÷ 15 min

• Output: 1 relay NO 16 A / 250 Vac

• Blocks for cables with maximum section of 4 mm

• Operating temperature: -10 °C ÷ 45 °C

• Operating humidity: 10% ÷ 90% not condensed

• Storage temperature: -10 °C ÷ 65 °C

• Container: 1 modules DIN

• Protection degree: IP20 / IP40 (on the front panel)

• Insulation: reinforced between accessible parts (front panel)

and all other terminals

• Type of actions: 1B

The positioning of the current transformer is essential for the correct operation of the instrument.

• The correct position of the current transformer within the electrical system is shown in the picture 1

• The direction of the produced current (i) is shown in the picture 2 (incoming current in the current transformer form the side indicated on the label)

• The current transformer must be connected to the terminals 5 and 6 of SOLAR-1 Micro (respect the polarity):

- terminal 5: white thread (+)

- terminal 6: black thread

Two loads or groups of loads must be identified as follows:

• not disconnectable load, that is the load which is always connected to the power line and which will not be released by the SOLAR-1 Micro

if the energy production is lower than necessary (its consumption must in any case be counted by the device to determine the total consumption).

• insertable load, which will be connected if the power surplus is higher than the setpoint.

information to users pursuant to art. 14 of the directive

2012/19 / EU of the european parliament and of the council

of 4 july 2012 on waste electrical and electronic equipment (WEEE)

If the crossed-out bin symbol appears on the equipment or packaging,

this means the product must not be included with other general

waste at the end of its working life.

The user must take the worn product to a sorted waste center,

or return it to the retailer when purchasing a new one.

Products for disposal can be consigned free of charge (without any new purchase obligation)

to retailers with a sales area of at least 400 m

2, if they measure less than 25 cm.

An efﬁ cient sorted waste collection for the environmentally friendly disposal of the used device

or its subsequent recycling, helps avoid the potential negative effects on the environment

and people’s health, and encourages the re-use and/or

recycling of the construction materials.

OPERATION LOGIC

Value:

(setpoint - hysteresis)

1 2

1 2 1 2 1 2

connection

load

zone

disconnection

load

zone

Time

Power

Setpoint value

Connection load

Disconnection load

Ton

4OPERATION

DEACTIVATION OF THE CONTROL

It is possible to disable relay switching which normally occurs

when the intervention threshold is exceeded.

• To enable this function, regulate the

Ton trimmer to the maximum value and

verify that the green LED flashes.

• To restore normal operation, reset the

Ton trimmer to the desired value

(and in any case lower than the maximum value)

and checking that the green LED is steady on.

DEFINITION AND MODIFICATION OF OPERATION PARAMETERS

• [kW] represents the activation threshold that is to say the minimum Setpoint

value of surplus of power necessary for connect the load

• (or differential) (kW) represents the value to subtract from the setpointHysteresis

to determine the disconnection zone (that is to say the zone where the load is

disconnected). This value can be set higher than the setpoint value.

This setting of SOLAR-1 Micro allows the use of all self-produced power and the use

of the remaining power from the low voltage grid.

• Ton [seconds] represents the period of time in which the power must be above

the setpoint before the load is actually switched on.

During this phase the red LED flashes.

Example 1: if the setpoint = 3 kW and differential = 0.5 kW the load eventually

connected is disconnected if the value of measured absorbed power is lower than 2.5 kW.

Example 2: if the setpoint = 3 kW and differential = 4 kW the load eventually connected

is disconnected if the value of measured absorbed power is lower than“-1 kW”

(1kW taken from the low voltage network). In this way the load will use all the

self-produced power and the power of 1 kW from the low voltage grid.

1 Terminals for load connection

2 Trimmer for setting the threshold (Set)

3 Trimmer for setting the release threshold of the load (Hyst)

4 Trimmer for setting the delay before inserting the load (Ton)

5 Terminals for voltage and current inputs

6 Signaling LEDs:

- green for power supply

- red for exceeded threshold indication

7 Toroid for the measurement of the current produced by

the system of generation net of the one absorbed by the load

2INSTRUMENT DESCRIPTION and DIMENSION

18 65

Vemer S.p.A.

I - 32032 Feltre (BL) • Via Camp Lonc, 16

e-mail: info@vemer.it - web site: www.vemer.it

V3IS01131-010

Mod. SOLAR-1 Micro

REFERENCE STANDARDS

Compliance with Community Directives:

2014/35/EU (LVD) and 2014/30/EU (EMCD)

is declared with reference to the following Standards:

• EN 61010-1 • EN 61000-6-2 • EN 61000-6-3

08-2022

Measurement

exchanged

energy

kWh

PdC

Current

transformer

kvarh

LV Network

Measurement

produced

energy

User loads

kWh

kvarh

Photovoltaic panels

picture 1

i = produced current

picture 2

Current transformer

picture 3

Connection diagram

LV Network = Low Voltage Network

CP = Connection Point

DG = General Device

Produkt Specifikationer

Mærke:	Vemer
Kategori:	Ikke kategoriseret
Model:	SOLAR-1 Micro

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer SOLAR-1 Micro stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Vemer Manualer

Vemer Mini Time Manual

20 Juni 2025

Vemer TCR Manual

2 Oktober 2024

Vemer Set PC RF8 Manual

1 Oktober 2024

Vemer ADR-D Vision Manual

22 September 2024

Vemer ES Manual

10 September 2024

Vemer Thalos RF Manual

3 September 2024

Vemer VE 502E Manual

1 September 2024

Vemer Elettrosonda Z Manual

25 August 2024

Vemer VE LAN Manual

10 August 2024

Vemer LCR048 Manual

10 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hendi 551813 Manual

2 November 2025

BougeRV E50 Manual

2 November 2025

Beverage-Air VueMax VMHC-7-1-G Manual

2 November 2025

OneConcept Magic-Carpet DX Manual

2 November 2025

Tonor T20 Manual

2 November 2025

Beverage-Air Horizon HRP3HC-1HS Manual

2 November 2025

Workzone AB1600 Manual

2 November 2025

Homedics BH-100-AU Manual

2 November 2025

Beverage-Air Horizon HFP1HC-1S Manual

2 November 2025

Beverage-Air VueMax VMHCSL-18-1-B Manual

2 November 2025