Parent unit main menu icons
Brightness
• You can change the brightness of
the parent unit screen.
LCD screen off timer
• You can set a specific time to
turn the screen off.
VOX sensitivity
• With this feature, you can
choose to hear sounds from the
baby unit all the time, or to hear
sounds that exceed a certain
level. You can use the parent
unit to adjust the microphone
sensitivity of your baby unit.
The higher the sensitivity level,
the more sensitive the baby
unit is in detecting sounds for
transmitting to the parent unit.
Sound-activated screen
• When the baby unit detects
no sound, the parent unit
screen stays off to save power.
Once a sound is detected, the
parent unit screen turns on
automatically. It will then turn
off again after 50 seconds of no
sound detection.
Temperature
• You can turn on the temperature
alert tone so that the parent
unit beeps whenever the room
temperature detected by the
baby unit falls outside of the
desired temperature range.
You can choose in Fahrenheit (oF)
or Celsius (oC) as the temperature
format displayed, or set the
maximum/minimum temperature
limit for alerts.
Parent unit warning icons and
messages
The selected baby unit is out
of range or is turned off.
The battery is empty and
needs to be recharged.
or
The temperature detected by
the baby unit is higher/lower
than the desired temperature
alert range.
The parent unit is searching
for baby units.
The parent unit is connected
to AC power.
Power on or off the baby unit
• Slide the switch to to turn onON/OFF ON the
baby unit. The LED light turns on.POWER
• Slide the switch to to turn off ON/OFF OFF
the baby unit. The LED light turns off.POWER
Power on or off the parent unit
• Slide the switch to to turn on the ON/OFF ON
parent unit. The screen and the LED POWER
light turns on.
• Slide the switch to to turn off ON/OFF OFF
the parent unit. The screen and the POWER
LED light turns off.
Adjust parent unit speaker volume
• Press VOL /VOL on the parent unit to
adjust the speaker volume.
• When the parent unit speaker volume is set to off,
appears on the screen.
Adjust LCD brightness
You can change the brightness of the parent
unit screen from to . The LCD Level 1 Level 5
brightness is preset to .Level 3
1. Press when the parent unit is idle.
2. Press or to choose , then press or
.
3. Press or to choose the desired level of
brightness, then press to confirm your
selection.
Screen off timer
You can set the screen off time for the parent
unit when there is no key press for a specific
time interval.
When the screen is turned off, you can still hear
sound from the baby unit.
1. Press when the parent unit is idle.
2. Press or to choose , then press or
.
3. Press or to choose the desired time
period to automatically turn off screen
( / - 5 min./ - 30 min. / - 60min.),
then press confirm your selection. to
Adjust the sound sensitivity of the
baby unit
You can choose to hear sounds from the baby
unit all the time, or to hear sounds that exceed a
certain level. You can use the parent unit to adjust
the microphone sensitivity of your baby unit. The
higher the sensitivity level, the more sensitive the
baby unit is in detecting sounds for transmitting to
the parent unit. The VOX sensitivity level is preset
to the highest level (Level 5).
Display Sensitivity Description
(Level 5) High
Sensitivity
Low
Sensitivity
Highest VOX
sensitivity level
The parent unit
speaker is constantly
on, and you will hear
all sounds (including
background noises)
from your baby’s room.
(Level 4) High VOX sensitivity
level
The parent unit
speaker turns on for
soft babbling and
louder sounds from
your baby. It remains
quiet when your baby
sleeps soundly.
(Level 3) Medium VOX
sensitivity level
The parent unit
speaker turns on for
loud babbling and
louder sounds from
your baby. It remains
quiet when your baby
makes soft sounds.
(Level 2) Low VOX sensitivity
level
The parent unit
speaker turns on for
crying and louder
sounds from your
baby. It remains quiet
when your baby
makes soft sounds.
(Level 1) Lowest VOX
sensitivity level
The parent unit
speaker turns on
for loud crying or
screeching sounds
from your baby. It
remains quiet when
your baby makes soft
sounds.
1. Press when the parent unit is idle.
2. Press or to choose , then press or
to open the submenu.
3. Press or to choose the desired sensitivity
level, then press to confirm your
selection.
• If the screen is off, and the setting of sound-activated
screen is , then LCD screen will be turned on ON
automatically when VOX sensitivity is triggered.
Turn on or off the sound activation
When sound activation is on, as long as no sound
is detected within 50 seconds, the parent unit
screen will turn off automatically to save power.
When your baby unit detects a sound, which
exceeds the selected sensitivity level, the sound
activation triggers the parent unit screen to turn
on automatically. When no sound is detected
within 50 seconds, the screen will be off again.
1. Press when the parent unit is idle.
2. Press or to choose , then press or
to open the submenu.
3. Press or to choose or , then press
to confirm your selection.
• If the sound sensitivity is set to the highest level,
the parent unit screen may remain on continuously
even though sound activation is on. This depends on
whether the baby unit detects any sounds
Zoom
You can zoom in while viewing images from the
baby unit.
• Press to zoom in.
• or to move the zoomed image Press
downward or upward.
• or to move the zoomed image Press
leftward or rightward.
• Press again to zoom out.
Talk
You can use the tion of the parent unit TALK func
to comfort your baby.
Press and hold on the parent unit. TALK
1. Speak towards the microphone on the parent
unit. Your voice is broadcast to the baby unit.
2. Release the TALK key to stop the broadcast.
Your baby unit monitors the temperature of your
baby’s room with its built-in temperature sensor.
If the detected temperature is out of the preset
temperature range, the parent unit will display
an alert message.
Set temperature range
You can set the desired minimum and maximum
room temperature alert ranges.
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press or
to open the submenu.
4. Press or to choose , then press or
.
5. Press or to choose the desired minimum
or maximum temperature, then press to
confirm your selection.
Temperature alert tone
You can turn on the temperature alert tone so
that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press or
to open the submenu.
4. Press or to choose or , then press
to confirm your selection.
Temperature format
You can choose to display the temperature in
Fahrenheit (o
F) or Celsius (oC).
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press or
to open the submenu.
4. Press or to choose or , then press
to confirm your selection.
The baby unit has infrared LEDs that allow you to
see your baby clearly at night or in a dark room.
When the baby unit being viewed detects low
light levels, the infrared LEDs are switched on
automatically. The images from the baby unit
are in black and white, and appears on the
screen.
NOTE
• It is normal if you see a short white glare on your
parent unit screen as the baby unit is adapting to
the dark environment.
• When the infrared LEDs are on, the images are in
black and white. This is normal.
• Depending on the surroundings and other
interfering factors, like lightings, objects, s and colour
backgrounds, the display resolution may vary. Adjust
the baby unit’s angle or place the baby unit at a
higher level to prevent glare and blurry display.
General product care
To keep this product working well and looking good,
follow these guidelines:
• Avoid putting it near heating appliances and
devices that generate electrical noise (for example,
motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit
in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
Storage
When you are not going to use the baby monitor for
some time, store the parent unit, the baby unit and the
adapters in a cool and dry place.
Frequently asked questions
Below are the questions most frequently asked about the
soother. If you cannot find the answer to your question,
please contact TecHelp on 1300 369 193.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed)
for common cure:
1. Disconnect the power to the
baby unit and the parent unit.
2. Wait a few seconds before
connecting power back to the
baby unit and the parent unit.
3. Turn on the baby unit and the
parent unit.
4. Wait for the parent unit to
synchronize with the baby unit.
Allow up to one minute for this to
take place.
Why don’t
the power-on
light of the
baby unit and
parent unit
go on when I
switch on the
units?
Perhaps the parent unit is not
connected to the power. Insert the
appliance plug into the parent unit
and put the adapter in a wall socket.
Then, slide the to switch ON/OFF
on the parent unit and to establish
connection with the baby unit.
Perhaps the baby unit is not
connected to the power. Insert the
appliance plug into the baby unit
and put the adapter in a wall socket.
Then, slide the switch to ON/OFF
ON to switch on the baby unit and
to establish connection with the
parent unit.
Why doesn’t
my parent
unit charge
while
connected to
AC power?
Make sure the power is not
controlled by a wall switch.
Why is my
screen in
black and
white?
The screen is in black and white
during night-time or in a dark room
when the night vision feature is
activated. This is normal.
Why do I get
glare or blurry
display on my
screen when
viewing my
baby at night?
During night-time or in a dark
room, the surroundings and other
interfering factors, like lightings,
objects, colours and backgrounds
may affect the image quality on
your parent unit screen. Adjust the
baby unit’s angle or place the baby
unit at a higher level to prevent
glare and blurry display.
Why does the
baby monitor
produce a
high-pitched
noise?
The parent unit and baby unit may
be too close to each other.
• Move the parent unit away from
the baby unit until the noise
stops; OR
• Turn down the volume of your
parent unit.
Why does the
parent unit
beep?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than 1 metre).
The parent unit may not have
enough charge for the parent unit
to perform normally. Charge the
battery in the parent unit for up to
11 hours.
The temperature of your baby’s
room may be too high or too low.
Why don’t I
hear a sound/
Why can’t I
hear my baby
cry?
The parent unit speaker volume may
be too low or off. Press
VOL to increase the volume, or
use the parent unit menu to change
sound sensitivity level to the highest
level (level 5).
Why can’t I
establish a
connection?
Why is the
connection
lost every
now and
then? Why are
there sound
interruptions?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than 1 metre).
Other electronic products may
cause interference with your baby
monitor. Try installing your baby
monitor as far away from these
electronic devices as possible.
Customer service and
product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
If you require assistance in operating this product,
please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at:
tcpsupport_au@vtech.com.
Voluntary Product Enquiry
In addition to your Statutory Rights and subject
to the conditions below, VTech warrants that this
product will be free from any defect in materials or
workmanship under conditions of normal use for a
period of 24 months from date of purchase.
VTech does not warrant that the product will be free
from defects if defects are caused by an accident,
misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care,
unauthorised modification, loss of parts, tampering
or attempted repair by a person not authorised by
VTech; or where the product has been damaged by
lightning or a mains power surge.To make a claim
under this Voluntary Product Warranty you must call
the TecHelp Information Line on 1300 369 193 or
contact VTech by e-mail at: tcpsupport_au@vtech.
com where a Customer Service Representative will
inform you of the product return process. You will
need to ensure that:
• You provide proof of purchase;
• Your product is suitably packaged (original
packaging is not required); and
• You have included all components from the
original purchase.
For your records
Date of purchase:
Place of purchase:
Serial number:
For Voluntary Product Warranty purposes, proof of
purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product
Warranty are in addition to other rights and remedies
that are available to you under law, which cannot be
excluded. The processes for this Voluntary Product
Warranty in no way limit your rights which arise as a
result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN 70
136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT
RETURN OR SERVICE ADDRESS – PLEASE CONTACT
TECHELP BY PHONE OR EMAIL FOR PRODUCT
AND WARRANTY SUPPORT. NO LIABILITY WILL BE
ACCEPTED BY VTECH FOR PRODUCTS RETURNED TO
THIS ADDRESS UNDER THIS VOLUNTARY PRODUCT
WARRANTY.
Phone number: 1300 369 193
Email address: tcpsupport_au@vtech.com
Statutory Rights
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 2402 - 2478.5 MHz Parent
unit: 2402 - 2478.5 MHz
Channels 52
LCD 2.4” Colour LCD
(QVGA 320x240 pixel)
Nominal
effective
range
Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirements
Parent unit: 3.6V Ni-MH battery
Baby unit power adapter: Output: 6V
DC @ 400mA
Parent unit power adapter: Output:
6V DC @ 400mA
Disposal of batteries and
product
The crossed-out wheelie bin symbols
on products and batteries, or on their
respective packaging, indicates they
must not be disposed of in domestic
waste as they contain substances that
can be damaging to the environment
and human health.
The chemical symbols Hg, Cd or
Pb, where marked, indicate that
the battery contains more than the
specified value of mercury (Hg),
cadmium (Cd) or lead (Pn) set out in
Battery Directive (2006/66/EC).
The solid bar indicates that the product
was placed on the market after 13th
August, 2005.
Help protect the environment by
disposing of your product or batteries
responsibly.
Specifications are subject to change without notice.
© 2020 VTech Telecommunications Ltd.
All rights reserved. 05/20. VM2700_AU_CIB_V3
