WAC Lighting Slant WS-W14911-BK Manual

WAC Lighting Lys Slant WS-W14911-BK

Læs gratis den danske manual til WAC Lighting Slant WS-W14911-BK (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 17 anmeldelser. Har du et spørgsmål om WAC Lighting Slant WS-W14911-BK, eller vil du spørge andre brugere om produktet?

Side 1/2
dweLED
www. .comdweLED
Phone 80 526.2588 • ( 0) Fax 26.2585 (800) 5
Headquarters/Eastern Distribution Center
44 Harbor Park DrivePort Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
dweLED r d o o a t comretains the ight to modify he t esign f ur oducts t pr a any time s art f p o he pany's continuous improvement program. Feb 2019
INSTALLATION INSTRUCTIONS
911-Outdoor Wall Sconce
WS-W14911/WS-W14911F
HARDWARE
Mounting Screw
Qty:1 Extra
Wire Connector
Qty: 3pcs+1 Extra
A
B
Silicon Gasket
Qty:1 Extra
C
1
G0
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
- Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by
dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqdans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou
accessoires non conçus pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer
l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
dweLED
www. .comdweLED
Phone 80 526.2588 • ( 0) Fax 26.2585 (800) 5
Headquarters/Eastern Distribution Center
44 Harbor Park DrivePort Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
dweLED r d o o a t comretains the ight to modify he t esign f ur oducts t pr a any time s art f p o he pany's continuous improvement program. Feb 2019
INSTALLATION INSTRUCTIONS
911-Outdoor Wall Sconce
WS-W14911
Fig.1
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for
installation.
CONNECTING THE WIRES (Fig. 2)
NOTE: The side of the mounting back plat e marked “GND” must face out.
5. Connect the fixture’s in wires to junction o wires as showput b x n ig. 2 (F). Make connsure that all wire ectors (A) are secure.
If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully
inside the junction box.
MOUNTING THE FIXTURE/ CONNECTING THE WIRE
6. Secure the canopy to the mounting plate using the mounting screw (B) and the silicone gasket (C).
7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to
outline the outside of fixture back plate where it meets the wall. Leave a space at a bottom to allow moisture to escape Fig.3.
Wire Connector
A
Junction Box Screw
Mounting Screw
B
Mounting Back
P
late
Junction Box
Silicon Gasket
C
Back Plate Dimensions
3. Remove the mounting screw B) and si ( licone gas ket (C) from the fixture.
4. Secure the mounting back plate to the junction x using bo the screws provided with the junction box.
Fig. 2 Wiring
Fixture Wires House Wires
Black or Black
Smooth (Hot)
Fixture Wires House Wires
White or White
Ribbed (Neutral)
Fixture Wires House Wires
Bare wire Green or Bare Copper
(Ground) (Ground)
Junction Box
Caulking
Fig.3
2G0


Produkt Specifikationer

Mærke: WAC Lighting
Kategori: Lys
Model: Slant WS-W14911-BK

Har du brug for hjælp?

Hvis du har brug for hjælp til WAC Lighting Slant WS-W14911-BK stil et spørgsmål nedenfor, og andre brugere vil svare dig