Warmup Tempo Manual

Warmup Termostat Tempo

Læs gratis den danske manual til Warmup Tempo (8 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Warmup Tempo, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

(1) (Turn clockwise to increase and anti clockwise to decrease.) Rotary Control

(2) Main Button

(3) control (only used during programming) Program Slide

(4) control Mode Slide

(5) Reset Button

(6) Replaceable CR2032 battery

Operating Guide:

for the Warmup Digital Programmable Thermostattempo

Part of the Element Series

Normally shows the current temperature in the room. This can be either the oor temperature or the air temperature. (See icon

4). When you are setting a program or manual temperature this icon will temporarily show the set temperature.

2. During programmed operation this thermometer will show whether the thermostat is at “Comfort” or “Setback” temperature.

The icon will be displayed when “Comfort -1/ -2 is the target temperature. (Only used with the Fil Pilote)

This icon is displayed when the heating is on.

4. These icons show the type of temperature regulation being used.

Floor Sensor Air Sensor

Regulator (This mode should only be used in special situations, please contact Warmup for additional information).

tempo

element

series TM

exclusively from

The has been designed with simplicity in mind and is highly intuitive in its programming. The sliders and simple rotary control tempo

make the setting of the thermostat quick and easy.

Introduction

ELT-01-XX-01 - Operating guide V1.0 © Warmup plc - 2013

5. These icons show the mode in which your thermostat is being used:

6. These icons show which time of day is being programmed.

7. This area shows the current time and day of the week.

8. These are error icons (see trouble shooting section) or special command icons:

Program mode will run the scheduled program

Manual mode will hold a xed temperature

Frost Protection will not allow the temperature to fall below 5°C

Standby mode

NOTE: When the thermostat displays both the manual and comfort icon the thermostat is in a manual override

and will hold a xed temperature until the next scheduled program period.

Morning

Fil Pilote

Floor sensor error

Overheat limit has been reached

There is no mains power

Battery is low

Getting started

In order to program the thermostat all you need to do is slide the control from the top position to the bottom tempo Program Slide

position, customising the program along the way.

If you make a mistake, return the control to the previous position and start again. In order to change a setting value, Program Slide

turn the . Pressing the Rotary Control Main Button will accept the value and move you on to the next value that needs setting.

The thermostat has a number of “Installer Settings”. If your thermostat has been installed correctly and is working then it is tempo

unlikely that you will need to change these again. For additional details see “ ” section.Installer settings

Your thermostat can be set so that the programming is done for “all days the same”, “weekday and weekend” or “7 day”. To change

this setting, see the section. “set time/day”

ELT-01-XX-01 - Operating guide V1.0 © Warmup plc - 2013

Day Evening Night

Produkt Specifikationer

Mærke:	Warmup
Kategori:	Termostat
Model:	Tempo

Har du brug for hjælp?

Hvis du har brug for hjælp til Warmup Tempo stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Warmup Manualer

Warmup Element Manual

22 Juli 2025

22 Juli 2025

22 Juli 2025

22 Juli 2025

21 Juli 2025

21 Juli 2025

17 December 2024

17 December 2024

27 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Fantini Cosmi C900R Manual

13 August 2025

GE RAK190V Manual

12 August 2025

Honeywell CT50K1028/E Manual

12 August 2025

Honeywell RET97B5D1002/U Manual

12 August 2025

Honeywell RCHT9510WFW2001/W Manual

12 August 2025

Honeywell CT87K1004/E1 Manual

12 August 2025

Honeywell YCT87N1006 Manual

12 August 2025

Honeywell RTH7500D1049/A Manual

12 August 2025

Honeywell YCT50K1006 Manual

12 August 2025

Honeywell RTH2510B1000/U Manual

12 August 2025