WyreStorm EXP-SW-0201 Manual

WyreStorm Router EXP-SW-0201

Læs gratis den danske manual til WyreStorm EXP-SW-0201 (1 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om WyreStorm EXP-SW-0201, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

EXP-SW-0x01-8K

WyreStorm Essentials 8K60 2x1 and 4x1 HDMI Switcher

Quickstart Guide

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

IMPORTANT! Installation Requirements

IMPORTANT! Wiring Guidelines

The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on HDMI

transmission limiting performance. Steps should be taken to minimize or remove these factors completely during installation for best results. WyreStorm

recommends using high quality WyreStorm Essentials 8K HDMI cables such as WyreStorm Essentials to ensure the highest content performance

available.

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

• Read through the section for important guidelinesWiring and Connections

before creating or choosing premade cables.

EXP-SW-0x01-8K Quickstart Guide | 220118

INT: +44 (0) 1793 230 343 | US: 844.280.WYRE (9973)

support@wyrestorm.com

In the Box

1x EXP-SW-0201-8K or EXP-SW-0401-8K

1x DC 12V PSU (US, UK, EU, AU)

1x IR Receiver Cable

1x IR Remote

1x 3-Pin Phoenix Connector (EXP-SW-0401-8K only)

2x Mounting Brackets (with screws)

1x Quickstart Guide (This Document)

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

RS-232 Wiring

The EXP-SW-0401-8K uses a 3-pin RS-232 with no hardware flow control.

Most control systems and computers are DTE where pin 2 is RX, this can vary

from device to device. Refer to the documentation for the connected device

for pin functionally to ensure that the correct connections can be made.

EDID Dip Switch Settings

The dipswitch on the splitter allows for changing the EDID management and downscaler on/off function.

Use the table below to congure the splitters EDID mode based on the application’s requirement.

When setting a dipswitch setting, power off the unit before making a change. Once set, the unit can be powered back on.

1. “-” indicates no adjustment is needed.

2. Reboot the device after setting the DIP switch

to make the settings take effect.

3. 3. Fixed EDIDs only include uncompressed

FRL video data. To transmit DSC compressed

FRL video, please use COPY EDID settings.

4. Fixed EDIDs all support audio formats up to

PCM 2CH and compressed audio up to 7.1CH.

Fixed EDIDs do not support HBR (High Bit

Rate) audio formats.

Function

DIP Switch Position

1 2 3 4

Auto-Copy EDID (Default) Up Up Up -

Fixed 4K@120Hz 4:4:4 10bit Up Up Down -

Fixed 8K@30Hz 4:4:4 10bit Down Up Down -

Fixed 8K@60Hz 4:2:0 10bit Down Down Down -

Fixed 4K@60Hz 4:4:4 8bit Up Down Up -

Fixed 1080P@60Hz Up Down Down -

Input audio extraction to S/PDIF

(Default)

- - - Up

ARC audio extraction to S/PDIF - - - Down

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to all devices in the system and that they are powered on.

• Verify that all HDMI connections are not loose and are functioning properly.

• If transmitting 8K, verify that the HDMI cables used are 3D or 8K rated.

• Ensure the EDID of the unit is correct. See for correct switch positions.EDID DIP Switch Settings

Troubleshooting Tips:

WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.

Produkt Specifikationer

Mærke:	WyreStorm
Kategori:	Router
Model:	EXP-SW-0201

Har du brug for hjælp?

Hvis du har brug for hjælp til WyreStorm EXP-SW-0201 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Router WyreStorm Manualer

WyreStorm MXV-0808-H2L Manual

13 September 2025

WyreStorm EXP-SW-0201 Manual

12 September 2025

WyreStorm EXP-SW-0401 Manual

12 September 2025

WyreStorm MX 0404-KIT Manual

12 September 2025

WyreStorm EXP-MX-0402-H2 Manual

30 Marts 2025

WyreStorm EXP-SW-0401-H2 Manual

22 Marts 2025

WyreStorm MX-0808-H2A Manual

3 September 2024

WyreStorm SW-540-TX Manual

1 September 2024

WyreStorm MX-0808 Manual

27 August 2024

Router Manualer

Nyeste Router Manualer

TP-Link Archer BE19000 Manual

6 December 2025

ZyXEL NR5111 Manual

29 November 2025

Festool MFKC 700 EB Manual

29 November 2025

Festool MFK 700 KA EQ Manual

27 November 2025

Festool OFKC 500 EB Manual

26 November 2025

Festool MFK 700 KA EB Manual

25 November 2025

ZTE T3000 Manual

21 November 2025

Vivanco 802.11g Manual

16 November 2025

Blustream WMF72 Manual

14 November 2025

EtherWAN EasyCell Manual

13 November 2025