Xantech HL85 Manual

Xantech Ikke kategoriseret HL85

Læs gratis den danske manual til Xantech HL85 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 54 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 27.5 anmeldelser. Har du et spørgsmål om Xantech HL85, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

MODEL

HL85

Hidden Link™ Shelf Top

Plasma/LCD/LED/CFL Friendly

IR Receiver

INSTALLATION INSTRUCTIONS

DESCRIPTION

The Hidden Link IR Receiver is a small shelf-top infrared repeater assembly. It

includes an IR receiver and a CB12 Connecting Block. The Hidden Link IR

Receiver is equipped with a 7-foot cable and a 3.5mm stereo mini plug, which

is plugged directly into the “IR RCVR” jack on the CB12. It can also be plugged

into the “AUX” or “IR RCVR” jack of other Xantech connecting blocks, such as

the models 789-44, CB60, and 791-44. The Hidden Link IR Receiver is

primarily intended for use in installations where the connecting block is within

reach of its 7-foot cable – as when installing the Hidden Link IR Receiver in a

cabinet where the controlled equipment is behind closed doors.

FEATURES

• Very small package, only 2.00”L x 3.15”W x 0.70”H.

• System testing red-talk-back LED.

• Includes CB12 Connecting Block for easy system installation.

SPECIFICATIONS

• Infrared carrier frequency bandwidth: 25 – 60 kHz.

• Reception range: Up to 80 feet, depending on remote control output

strength and ambient conditions.

• Nominal reception angle: 55 degrees o axis.

• Cable requirements: See “INSTALLATION” below.

• Max. transmission length: 1 mile using 18 gauge wire.

• Maximum current output: 100mA

• Drives IR emitters through Xantech Connecting Blocks, Controllers, etc.

• Dimensions: 2.00”x3.15”x0.70” (51mm x 80mm x 18mm)

• Power requirements: +12VDC, 20mA.

INSTALLATION

QUICK-START

A typical system will use an IR receiver, several emitters, and a power supply

all connected to a connecting block.

1. Connect the IR receiver to the “IR RCVR” port on the connecting block.

The ‘red’ connector is installed to the ‘red’ plug.

Note: In some extended distances, additional 3-conductor may be required and can be

connected to the terminals on the connecting block.

2. Connect the Emitters to the connecting block. The ‘yellow’ connector is

installed to the ‘yellow’ plug.

3. Connect the power supply to the connecting block.

4. Installation complete

LOCAL SYSTEM APPLICATION

In this system a 286D Dual Blink-IR Designer Emitter is shown connected to

the “OUT” jack. A single emitter could also be used, such as the model 282D or

283D. If expansion beyond two emitters is required, use a Xantech 789-44,

CB60, or 791-44 Connecting Block in place of the CB12. Do not use the CB12

in this case.

781ERGPS

To 120 VAC

(Unswitched)

Emitter

L Series

DVD

CABLE CONNECTIONS

HL2’s may also be used where the 7-foot cable is not long enough. Simply cut

o the mini plug, strip the leads and splice them to a 3-conductor extension

cable with a terminal block or other means. Then connect the extension cable

to the 3-terminal block on the CB12 as shown in the figure below.

3.5mm mini plug Signal Name Wire Color

TIP SIGNAL WHITE

RING GROUND BLACK

SLEEVE +12VDC RED

The 3-conductor inter-room cable (24 gauge up to 200’, 22 gauge up to 600’,

20 gauge up to 2000’, 18 gauge up to 5000’), is run to the main room.

While it is possible to make wired connections without the connecting block, it is

not recommended. The connecting block reduces installation time, helps to

eliminate errors, allows easy troubleshooting and permits easy system

upgrades later, if needed.

L Series

Produkt Specifikationer

Mærke:	Xantech
Kategori:	Ikke kategoriseret
Model:	HL85

Har du brug for hjælp?

Hvis du har brug for hjælp til Xantech HL85 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Xantech Manualer

Xantech 791-44 Manual

29 August 2024

Xantech DL85K Manual

29 August 2024

Xantech XT-DIG-11 Manual

29 August 2024

Xantech 282D Manual

29 August 2024

Xantech XT-HDMI-MX42-4K18G Manual

29 August 2024

Xantech XSS26100W Manual

28 August 2024

Xantech 283D Manual

28 August 2024

Xantech 17294 Manual

28 August 2024

Xantech 284D Manual

28 August 2024

Xantech SPLCDCB100 Manual

28 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Festo SOEG-S-M18W-S-L Manual

18 August 2025

Festo SIED-M30NB-ZO-S-L Manual

18 August 2025

Parkside PFBSA 4 A1 Manual

18 August 2025

Martin VC-Dot 4 Manual

18 August 2025

Smart-AVI QKVM-DP Manual

18 August 2025

Festo SOEG-RTH-M18-NS-S-2L Manual

18 August 2025

Festo CPV10-VI-P4-M7-D Manual

18 August 2025

D-Link DI-206 Manual

18 August 2025

Royal Catering RCWF-10LE-H Manual

18 August 2025

Festo SIED-M30B-ZO-K-L Manual

18 August 2025