Access Lighting Grid 20049LEDDMG Manual

Access Lighting Lys Grid 20049LEDDMG

Læs gratis den danske manual til Access Lighting Grid 20049LEDDMG (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Access Lighting Grid 20049LEDDMG, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
WHAT YOU NEED
•
Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
INSTALLATION INSTRUCTIONS
WHAT WE PROVIDE
•
Mounting Hardware
• LED
COLLECTION
CERTIFICATION: cETLus WET
NO. 20049LEDDMG
GRID
20049LEDDMG
APPLICATION MODEL NO.
Wall Fixture
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that
you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care, are factors that can’t be built into any product. These factors must
be supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
Recognized.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
Recommended Dimmers
Lutron Maestro MACL-153MH
Lutron Maestro MAELV-600-WH
Leviton SureSlide NO.6672
MOUNT CROSSBAR AND WIRE CONNECTIONS
If there is an existing fixture remove it. Expose the supply wires
from the J-box.
Mount the crossbar to the J-box with the
supplied screws. Connect the black supply wire to the black
fixture wire. Secure with the supplied wire nuts. Connect the
white supply wire to the white fixture wire. Secure with the
supplied wire nuts. Attach the green J-Box wire around
green hexagonal head screw or connect it to the green
supply grounding wire of the fixture.
Secure all wire with electrical tape (not supplied).
Tuck all wires carefully into the J-Box.
CERTIFICATION: cETLus WET
NO. 20049LEDDMG
MOUNT FIXTURE TO CROSSBAR
Position the fixture over the crossbar.
Align the holes on the side of the
fixture and secure with the supplied screws.
**This fixture is wet location rated. In order to ensure
that moisture does not enter the outlet box and cause
a short circuit, clear caulking should be used to seal the
space between the fixture mounting bracket and the
wall. Ensure that a space is left at the bottom to allow
for the escape of moisture. It is recommended that
Outdoor Silicon Sealant is used for that purpose**
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS LIGHTING FIXTURE
If the fixture is to be removed or replaced,
please ensure that the electricity is
switched off and that the fitting is cool
before touching it.
CAUTION
VER: 18.12.1

Produkt Specifikationer

Mærke: Access Lighting
Kategori: Lys
Model: Grid 20049LEDDMG

Har du brug for hjælp?

Hvis du har brug for hjælp til Access Lighting Grid 20049LEDDMG stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lys Access Lighting Manualer

Access Lighting

Access Lighting Atom 20725LEDDLP Manual

30 Juni 2025
Access Lighting

Access Lighting Simplicite 50937 Manual

29 Juni 2025
Access Lighting

Access Lighting Aero 20670LEDDLP Manual

27 Juni 2025
Access Lighting

Access Lighting Arc 62516LEDD Manual

27 Juni 2025
Access Lighting

Access Lighting Bi-Punch 62238LEDD Manual

27 Juni 2025
Access Lighting

Access Lighting Elementary 20419 Manual

27 Juni 2025
Access Lighting

Access Lighting Grid 20049LEDDMG Manual

26 Juni 2025

Lys Manualer

Nyeste Lys Manualer

V-TAC

V-TAC VT-10176 Manual

13 August 2025
Eurolite

Eurolite LED IP TMH-H420 Manual

13 August 2025
Eurolite

Eurolite LED Silent Par 6 QCL Floor Manual

13 August 2025
Neewer

Neewer FS600C Manual

13 August 2025
Eurolite

Eurolite LED IP PAR 12x8W QCL Manual

13 August 2025
Philips

Philips Ultinon Essential LED 11258UE2X2 Manual

13 August 2025
Plus More

Plus More MO-HF024 Manual

13 August 2025
Philips

Philips Ultinon Essential LED 11362UE2X2 Manual

12 August 2025
Philips

Philips Ultinon Essential LED 11005UE2X2 Manual

12 August 2025
GLP

GLP Fusion Creos Manual

12 August 2025