Aguilar AG 500 Manual

Aguilar Modtager AG 500

Læs gratis den danske manual til Aguilar AG 500 (7 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Aguilar AG 500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

Page 1

English

Thank you for purchasing the AG 5 V2 amplifier! 00

Characterized by its clarity, dynamic range, and fast transient response,

this superlight amplifier b an incredibly flexible EQ section, the AG 5oasts 00

features controls for Treble, High Mid, Low Mid and Bass along with Deep

and Bright EQ switches for a broadband boost. This solid-state amplifier

provides 500 continuous watts at either 4 or 2.67 ohms, boasts an incredibly

flexible EQ section, and features a series effects loop, dual XLR balanced

outputs, an AUX input, Headphones output, as well as a rear panel

Speakon output, and our Aguilar Cabinet Suite IR Module.

Table of Contents

I. Important Safety Instructions page 2

II. Getting Started page 3

A. Manual Conventions

B. Basic Setup

C. Protection Features

III. Features and Functions page 4

A. Front Panel

B. Rear Panel

IV. Warranty Information page 6

V. Environmental Protection page 6

Page 2

I. Important Safety Instructions

WARNING: To reduce the risk of fire or electric shock, do not expose

equipment to rain or moisture. Aguilar Amplification assumes no

responsibility for any damage or injury that results from improper

use or service.

CAUTION: RISK OF ELECTRIC SHOCK! DO NOT OPEN! There are no user

serviceable parts inside of this product. This is a high voltage

device, and internal voltages can be lethal. Any and all work

should be performed by qualified personnel only.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

14. Vents are provided for heat dissipation on the sides, and at the rear of the amplifier.

Maintain at least a 2” (5cm) space around these vents to provide sufficient

ventilation.

15. Make sure that the power cord is intact before plugging it into the unit. Do not use a

cord with visible damage to its insulation, or connectors.

16. The equipment shall be connected to a MAINS socket outlet with a protective

earthing connection. This is a Class I device, equipped with a safety feature that

requires the use of the three-pin grounding power plug.

17. Use only accessories listed in this manual, or in other way specified by the

manufacturer.

18. Do not install this amplifier on carts or other moving objects.

19. Where the MAINS plug or an appliance coupler is used as the disconnect device, the

disconnect device shall remain readily operable. To completely disconnect the

equipment from the AC mains, remove the power cord from the AC receptacle.

20. Do not use this device with wall/ceiling mounts not specified by the manufacturer.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that

may cause undesirable operation.

Produkt Specifikationer

Mærke:	Aguilar
Kategori:	Modtager
Model:	AG 500

Har du brug for hjælp?

Hvis du har brug for hjælp til Aguilar AG 500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Aguilar Manualer

Aguilar AG 500 Manual

10 Juli 2025

Aguilar AG Preamp Manual

10 Marts 2025

Aguilar Tone Hammer Preamp Manual

10 Marts 2025

Aguilar Tone Hammer 500 V2 Manual

9 Marts 2025

Aguilar OBP-1 Manual

9 Marts 2025

Aguilar AG 700 V2 Manual

9 Marts 2025

Aguilar OBP-2 Manual

9 Marts 2025

Aguilar OBP-3 Manual

9 Marts 2025

Modtager Manualer

Nyeste Modtager Manualer

Lectrosonics DSR-A1B1 Manual

10 Juli 2025

Lectrosonics DSR-961 Manual

10 Juli 2025

Teac AP-507 Manual

10 Juli 2025

Ecler eLPA2-950 Manual

10 Juli 2025

Lectrosonics DSR-941 Manual

10 Juli 2025

Lectrosonics DSR-B1C1 Manual

10 Juli 2025

Twelve South AirFly Pro 2 Manual

10 Juli 2025

Extron DA2 HD 8K AE Manual

10 Juli 2025

Hartke TX7500 Manual

10 Juli 2025

DB Technologies IA504R Manual

10 Juli 2025