Aguilar Tone Hammer 500 V2 Manual

Aguilar Modtager Tone Hammer 500 V2

Læs gratis den danske manual til Aguilar Tone Hammer 500 V2 (7 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Aguilar Tone Hammer 500 V2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

Page 1

English

Thank you for purchasing the Tone Hammer 5 V2 amplifier! 00

Characterized by its warm, tube-like tone and character this superlight

amplifier combines three bands of flexible EQ, our signature “Drive” control

for added punch and grit, and 500 watts of power in a 4 lb. ( 9 kg.) .2 1.

package. This solid-state amplifier provides 500 watts at either continuous

4 or 2.67 ohms, boasts an incredibly flexible EQ section, and features a

series effects loop, dual XLR balanced outputs, an AUX input, Headphones

output, as well as a rear panel Speakon output, and our Aguilar Cabinet

Suite IR Module.

Table of Contents

I. Important Safety Instructions page 2

II. Getting Started page 3

A. Manual Conventions

B. Basic Setup

C. Protection Features

III. Features and Functions page 4

A. Front Panel

B. Rear Panel

IV. Warranty Information page 6

V. Environmental Protection page 6

Page 2

I. Important Safety Instructions

WARNING: To reduce the risk of fire or electric shock, do not expose

equipment to rain or moisture. Aguilar Amplification assumes no

responsibility for any damage or injury that results from improper

use or service.

CAUTION: RISK OF ELECTRIC SHOCK! DO NOT OPEN! There are no user

serviceable parts inside of this product. This is a high voltage

device, and internal voltages can be lethal. Any and all work

should be performed by qualified personnel only.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

14. Vents are provided for heat dissipation on the sides, and at the rear of the amplifier.

Maintain at least a 2” (5cm) space around these vents to provide sufficient

ventilation.

15. Make sure that the power cord is intact before plugging it into the unit. Do not use a

cord with visible damage to its insulation, or connectors.

16. The equipment shall be connected to a MAINS socket outlet with a protective

earthing connection. This is a Class I device, equipped with a safety feature that

requires the use of the three-pin grounding power plug.

17. Use only accessories listed in this manual, or in other way specified by the

manufacturer.

18. Do not install this amplifier on carts or other moving objects.

19. Where the MAINS plug or an appliance coupler is used as the disconnect device, the

disconnect device shall remain readily operable. To completely disconnect the

equipment from the AC mains, remove the power cord from the AC receptacle.

20. Do not use this device with wall/ceiling mounts not specified by the manufacturer.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that

may cause undesirable operation.

Produkt Specifikationer

Mærke:	Aguilar
Kategori:	Modtager
Model:	Tone Hammer 500 V2

Har du brug for hjælp?

Hvis du har brug for hjælp til Aguilar Tone Hammer 500 V2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Aguilar Manualer

Aguilar AG 500 Manual

10 Juli 2025

Aguilar AG Preamp Manual

10 Marts 2025

Aguilar Tone Hammer Preamp Manual

10 Marts 2025

Aguilar Tone Hammer 500 V2 Manual

9 Marts 2025

Aguilar OBP-1 Manual

9 Marts 2025

Aguilar AG 700 V2 Manual

9 Marts 2025

Aguilar OBP-2 Manual

9 Marts 2025

Aguilar OBP-3 Manual

9 Marts 2025

Modtager Manualer

Nyeste Modtager Manualer

Ram Audio MDi8-6K Manual

13 August 2025

Tangent Ampster TV II Manual

13 August 2025

Ram Audio Pi4-6K D Manual

13 August 2025

Ram Audio MDi8-2K7 D BS/P Manual

13 August 2025

Audiolab 8300MB Manual

13 August 2025

ESX Signum SE1500.1 Manual

13 August 2025

Pyle PFOCUS16 Manual

12 August 2025

Musical Fidelity B1xi Manual

12 August 2025

Artsound MX60MKII Manual

12 August 2025

NAD CI 8-120 DSP V2 Manual

12 August 2025