Atlas Sound I8SM+ Manual


Læs gratis den danske manual til Atlas Sound I8SM+ (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 78 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 39.5 anmeldelser. Har du et spørgsmål om Atlas Sound I8SM+, eller vil du spørge andre brugere om produktet?

Side 1/4
1/4
AtlasIED.com
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
1601 JACK MCKAY BLVD.
ENNIS, TEXAS 75119 U.S.A.
©2015 Atlas Sound L.P. and Innovative Electronic Designs, LLC. All Rights Reserved. Atlas Sound is a trademark of Atlas Sound L.P. IED is a registered trademark of Innovative Electronic Designs, LLC. All other trademarks are the property of their respective owners.
All specs are subject to change without notice. ATS005301 RevA 10/15 P/N 493870
Introduction
AtlasIED IP loudspeakers consist of a factory assembled loudspeaker and baffle with PCB amplifier / control board securely mounted to the rear of
the baffle. The amplifier / control board is capable of producing 15-watts RMS into the 8Ω loudspeaker with IEEE 802.3at compliant PoE switches. A
local 24VDC PSU (TSD-PS24V2500MA) may also be used instead of PoE switches. Interconnection is via a board mounted female RJ-45 connector. All
models are compatible with AtlasIED’s Global ControlKom
©
, GCK
©
, Syn-Apps SA-Announce
©
, Singlewires InformaCast
©
software, and SIP standalone
operation. They also include 2 general purpose inputs, 1 relay output, 1 line out, and 1 line input.
Models may include the following:
8" Loudspeaker
6" Horn Speaker
LED Display
• Microphone
• Flasher
Functionality
Before installing, note the unit’s MAC address found on the units main circuit board (example 00:02:C1:81:00:00). Once connected to a network and
powered, the IP loudspeaker will boot up and automatically obtain an IP address from a DHCP server on the network. Next, the unit will start the
registration process to find the controller software. Once the IP loudspeaker identifies the software’s location, it will send a registration request to the
software and register. The MAC address of the unit will then show in the software. Please refer to the installation manual of the software for additional
configuration settings.
After the module has registered with the software, its HTTP page can be accessed by navigating to its IP address with any Internet browser. This page
will show its current firmware version and registration information. If unsure about IP address, press the unit’s service button for 1 second. The unit’s
IP address will be announced over the loudspeaker.
A. Power Input (WARNING: Do not use in conjunction with PoE)
B. General Purpose Inputs 1 and 2
C. Relay Output
D. Line Level In
E. Line Level Out
F. Loudpeaker Outputs - The primary output is connected to the baffle loudspeaker (or horn). The secondary output may be used to drive another 8Ω
loudspeaker or horn.
G. Network Input
H. Service Switch
I. Force Discovery Jumpers (A,B,C)
IP Loudspeakers
A
I
F BDG H
E C
2/4
AtlasIED.com
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
1601 JACK MCKAY BLVD.
ENNIS, TEXAS 75119 U.S.A.
©2015 Atlas Sound L.P. and Innovative Electronic Designs, LLC. All Rights Reserved. Atlas Sound is a trademark of Atlas Sound L.P. IED is a registered trademark of Innovative Electronic Designs, LLC. All other trademarks are the property of their respective owners.
All specs are subject to change without notice. ATS005301 RevA 10/15 P/N 493870
GPI Interface
General purpose inputs (GPI’s) are used to trigger events in the Control software packages. Refer to software manuals for functionality.
Relay Output is Controlled via software packages. Refer to software manuals for functionality.
Mounting
Each model has a specific mounting enclosure that can be Flush Mount, Surface Mount Straight, or Angled Surface Mount. Models include:
Flush Mount Enclosures: FEST-IH, FEST-I8S, FEST-I8SC
Surface Mount Enclosures: SEST-IH, SEST-I8S, SEST-I8SC
Surface Mount Angled Enclosures: SEA-I8S, SEA-I8SC
Note: The I128SYS+ series is sold with an integrated enclosure for drop ceilings.
IP Loudspeaker Connector Block Pin Configuration
A 14 pin screw type connector block (J2) will be used to allow connections to the controller.
Pin Description
1 GPI In 2 + 8 Line-In (+)
2 GPI In 2 Com 9 Line-Out (-)
3 GPI In 1 + 10 Line-Out (+)
4 GPI In 1 Com 11 Primary / Loudspeaker (-)
5 Relay Common 12 Primary / Loudspeaker (+)
6 Relay Normally Open 13 Secondary / Loudspeaker (-)
7 Line-In (-) 14 Secondary / Loudspeaker (+)
Note: Pin 14 is located next to the RJ45 jack.
Misc Settings
1. Service Button - The only push switch located on the main circuit board.
• Press 1 sec - The current IP address will be spoken (in English) through the 8Ω loudspeaker
Press 10 sec - Factory reset
Press and hold while applying power - Hold the button until the Status LED on the circuit board starts blinking rapidly to perform a factory
reset without any servers present
2. Force Discovery - In some cases, auto discovery may not work correctly. In these cases, the A, B, and C jumper located under the service button
may be enabled.
Jumper A - Singlewire
Jumper B - Syn-Apps
Jumper C - GCK
General Specifications
Weight I8S+, I8SM+ – 4.8 lbs
I8SC+, I8SCM+ – 6 lbs
I128SYS+, I128SYSM+ – 12.9 lbs
IHVP+ - 6.1 lbs


Produkt Specifikationer

Mærke: Atlas Sound
Kategori: Højttaler
Model: I8SM+

Har du brug for hjælp?

Hvis du har brug for hjælp til Atlas Sound I8SM+ stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler Atlas Sound Manualer

Højttaler Manualer

Nyeste Højttaler Manualer