Atlona AT-VCC-IR-KIT Manual

Atlona Ikke kategoriseret AT-VCC-IR-KIT

Læs gratis den danske manual til Atlona AT-VCC-IR-KIT (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Atlona AT-VCC-IR-KIT, eller vil du spørge andre brugere om produktet?

Side 1/12
Installation Guide
AT-VCC-IR-KIT
1
IP to IR Command Converter for Velocity Control System
AT-VCC-IR-KIT
The Atlona AT-VCC-IR-KIT is an accessory for the Atlona Velocity™ Control System that provides
conversion from IP control commands to IR. This Velocity Control Converter is very compact
and can be placed anywhere a device requires IR control. The VCC-IR-KIT is remotely powered
through Power over Ethernet (PoE), or locally from a USB power source. The primary unit installs
onto any surface via a convenient mounting dock. A simple “click” locks it into place for a secure,
reliable installation. The IR adapter module includes three 3.5 mm ports for connecting the AT-
VCC-IR-EMT emitters. Each port is independently addressable, allowing discrete IR control of
three dierent AV devices.
1 x AT-VCC
1 x AT-VCC-IR
Package Contents
Operating Notes
The Velocity Command Converter must be on the same network as the Velocity Gateway
(AT-VGW-250) or it will be unable to sync for control.
The AT-VCC-IR-KIT is PoE, to power the unit, simply plug it into a PoE compatible network
switch. If the network switch is not PoE capable, a PoE injector or USB (purchased separately)
can be used.
All devices (AT-VCC, Velocity, AT-VTP, switchers, etc) should be set to static IPs or the
DHCP IP address reserved for each individual device.
IMPORTANT: Velocity Gateway (AT-VGW-250) must be set up before the AT-VCC-IR-KIT
is fully functional.
Installation Guide
AT-VCC-IR-KIT
2
2 3 41 5 6
1 IR Window
Use to learn IR commands from a device’s
IR remote control.
2 Ethernet
Connect an Ethernet cable from this
port to the same network as the Velocity
Gateway.
3 USB
Can be used to power the VCC when PoE
is unavailable. Requires 5V DC @ 250mA
(not supplied).
4 3.5mm Port
Connect to a VCC IR connector or
optional IR emitter - AT-VCC-IR-EMIT
(purchasable through atlona.com).
5 3.5mm Connector
Connect the 3.5mm connector to the
3.5mm port of the VCC.
6 3 x 3.5mm Ports
Connect up to three 3.5mm IR receivers to
the 3-3.5mm ports.
Panel Description
IP
The AT-VCC is set to DHCP by default. If the network does not support DHCP, it will
automatically set the AT-VCC to the static IP of after 30 seconds.
192.168.1.70
VHelp and webGUI
Velocity will nd the VCC when scan network is used, but if the VCC needs to be set up o site
rst, the software VHelp can be used.
1 Connect the IR tri-port or IR emitter into the 3.5mm port on the unit.
2 Connect the AT-VCC to a network switch (PoE is best if a PoE switch is not available, a
power injector or mini USB to USB cable may be used).
3 Download VHelp from the resource tab of https://atlona.com/product/AT-VCC-IR-KIT.
4 Unzip the le to the local PC
5 Double-click the VHelp executable to open the program. Vhelp will start discovery as soon
as the program is opened.


Produkt Specifikationer

Mærke: Atlona
Kategori: Ikke kategoriseret
Model: AT-VCC-IR-KIT

Har du brug for hjælp?

Hvis du har brug for hjælp til Atlona AT-VCC-IR-KIT stil et spørgsmål nedenfor, og andre brugere vil svare dig