Bogen MPS1 Manual

Bogen Højttaler MPS1

Læs gratis den danske manual til Bogen MPS1 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Bogen MPS1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Specifications subject to change without notice.

54-2194-01A 1010

MPS1

Mini Pendant Speaker

Models MPS1B /MPS1W

Installation and Use Manual

Power Tap Selection

16-ohm or 70V

The Power Tap selector switch is used to set the

appropriate power level or impedance for your

system. Rotate the switch until the power level

you require lines up with arrow.

IMPORTANT: When connecting to a 70V amplifier,

make sure that the MPS1 Tap Selector switch

IS NOT set in the “16Ω” position.

Speaker Connection and Polarity

Speaker wiring is terminated at a snap-lock input

connector, with a positive and negative terminal.

All wiring should be done prior to installation and

then plugged into the rear of the MPS1. Wire all

speaker polarities the same way.

70V System Configurations

When designing a 70V system, the total of all power tap settings of all the connected

speakers CANNOT EXCEED the output power of the 70V amplifier (amplifier power

can exceed the sum of the speaker loads).

Low-Impedance System Configurations

When wiring together multiple MPS1 speakers that are set to 16 ohms, it is important to

calculate (using Ohmʼs Law) the total load that these speakers present to the amplifier.

The total load impedance of the interconnected speakers cannot be lower than the

minimum load impedance rating of the low-impedance amplifier. Also, care must be

taken to ensure the amplifier cannot overdrive the speakerʼs maximum power rating.

POWER TAP

SELECTOR SWITCH

SNAP-LOCK

WIRING TERMINAL

MPS1

(Top View)

EXAMPLE: 16 + 32 + 8 + 8 + 16 = 80 Watts minimum amplifier output rating.

EXAMPLE: Four 16 -ohm speakers in parallel = 4 ohms. Also in this example,

the maximum amplifier output power rating should not exceed 200W (4 X 50W,

the MPS1 max. power is 50W).

__ +

Produkt Specifikationer

Mærke:	Bogen
Kategori:	Højttaler
Model:	MPS1

Har du brug for hjælp?

Hvis du har brug for hjælp til Bogen MPS1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Bogen Manualer

Bogen VRS3 Manual

11 Marts 2025

Bogen MB8TSL(VR) Manual

1 Marts 2025

Bogen FG20W Manual

1 Marts 2025

Bogen FG20B Manual

1 Marts 2025

Bogen CSD2X2U-V2 Manual

1 Marts 2025

1 Marts 2025

1 Marts 2025

1 Marts 2025

28 Februar 2025

10 December 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Renkforce RL100W Manual

14 August 2025

Pioneer TS-A1081F Manual

14 August 2025

Bose Bluetooth Audio adapter Manual

14 August 2025

Bose DesignMax DM8C-SUB Manual

14 August 2025

Bose DesignMax DM2C-LP Manual

14 August 2025

Bose Virtually Invisible 691 Manual

14 August 2025

Crosley Flashback CR3051A Manual

13 August 2025

Russound IC-820T Manual

13 August 2025

Russound SB-C67 Manual

13 August 2025

Coastal Source RSUB8 Manual

13 August 2025