Bogen MPS2 Manual

Bogen Højttaler MPS2

Læs gratis den danske manual til Bogen MPS2 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Bogen MPS2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Specifications subject to change without notice.

54-2194-01C 1307

MPS1, MPS2

Mini Pendant Speakers

Models MPS1B /MPS2B ,(Black)

MPS1W/MPS2W (White)

Installation and Use Manual

Power Tap Selection

16-ohm or 70V

The Power Tap selector switch is used to set the

appropriate power level or impedance for your

system. Rotate the switch until the power level

you require lines up with arrow.

IMPORTANT: When connecting to a 70V amplifier,

make sure that the Tap Selector switch on the

speaker IS NOT set in the “16Ω” position.

Speaker Connection and Polarity

Speaker wiring is terminated at a snap-lock input

connector, with a positive and negative terminal.

All wiring should be done prior to installation and

then plugged into the rear of the speaker. Wire all

speaker polarities the same way.

70V System Configurations

When designing a 70V system, the total of all power tap settings of all the connected

speakers CANNOT EXCEED the output power of the 70V amplifier (amplifier power

can exceed the sum of the speaker loads).

Low-Impedance System Configurations

When wiring together multiple MPS1/2 speakers that are set to 16 ohms, it is important to

calculate (using Ohmʼs Law) the total load that these speakers present to the amplifier.

The total load impedance of the interconnected speakers cannot be lower than the

minimum load impedance rating of the low-impedance amplifier. Also, care must be

taken to ensure the amplifier cannot overdrive the speakerʼs maximum power rating.

POWER TAP

SELECTOR SWITCH

SNAP-LOCK

WIRING TERMINAL

MPS1/2

(Top View)

100W Amplifier

with 70V Output

200W Max. Low-Impedance

Amplifier

4-ohm direct

GND

EXAMPLE: 16 + 32 + 8 + 8 + 16 = 80 Watts minimum amplifier output rating.

EXAMPLE: Four 16 -ohm speakers in parallel = 4 ohms. Also in this example,

the amplifier output power rating capability should not exceed 200W (4 X 50W,

the MPS1/2).

Produkt Specifikationer

Mærke:	Bogen
Kategori:	Højttaler
Model:	MPS2

Har du brug for hjælp?

Hvis du har brug for hjælp til Bogen MPS2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Bogen Manualer

Bogen MB8TSL(VR) Manual

1 Marts 2025

Bogen FG20W Manual

1 Marts 2025

Bogen FG20B Manual

1 Marts 2025

Bogen CSD2X2U-V2 Manual

1 Marts 2025

1 Marts 2025

1 Marts 2025

1 Marts 2025

28 Februar 2025

10 December 2024

Bogen NEAR S5T Manual

23 September 2024

Højttaler Manualer

Nyeste Højttaler Manualer

DS18 PRO-NEO6R Manual

18 Juni 2025

Ground Zero GZRF 69SQX Manual

18 Juni 2025

MB Quart NF1-116SB Manual

18 Juni 2025

Sogo SS-8586 Manual

17 Juni 2025

MB Quart NK2-116W Manual

17 Juni 2025

MB Quart NF1-116SW Manual

17 Juni 2025

Sogo SS-8585 Manual

17 Juni 2025

MB Quart NHT1-120BPR Manual

17 Juni 2025

DS18 PRO-X8.4RGBCAP Manual

17 Juni 2025

Sogo SS-8590 Manual

17 Juni 2025