Boston Acoustics KIT-JB-15 Manual

Boston Acoustics Guitarforstærker KIT-JB-15

Læs gratis den danske manual til Boston Acoustics KIT-JB-15 (3 sider) i kategorien Guitarforstærker. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Boston Acoustics KIT-JB-15, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

KIT-JB-15

Tools needed

Small Phillips screwdriver

Big Phillips screwdriver

Soldering iron and solder

Wrench

Hammer

How great would it be to build your own bass and then storm the stage with it? Even if you

are a dreadful handyman, you can use the DIY kit from Boston. It does not need to be cut,

drilled or milled, as it is all done for you.

The neck is already equipped with frets and neck and the body is already aligned. All

supplies (except equipment) are included in the package such as pickups, screws, poten-

tiometers, tuners and strings. Furthermore you can of course enjoy them with paint and/or

specify the colour or gloss you want. If you wish to continue viewing the wood grain, then

the clear coat is an excellent choice to emphasize the grain of the wood. The DIY guitar

Boston is a fun, easy and creative way to create your own unique bass.

body : mahogany

neck : USA maple

ngerboard : pau ferro

pickups : 2 x single coil

hardware : chrome

Wood

First shape the headstock to your liking. Use les or saws and sanding paper to make your

headstock design neat and tidy. Make sure you remove all saw and sanding marks. This will

be your signature on this guitar, take your time!

Sanding and nishing

Take the loaded pickguard o your guitar. Sand the body and neck with 320 grit dry

sanding paper. After this step, use masking tape to guard those parts that you don’t want

to colour/nish. Always follow the instructions on your nishing product, be it staining,

spraying with aerosol cans or nishing in a spraying booth. After the body and neck have

been nished in the colour and gloss of your choice, and you have polished your guitar to

the desired result, it’s time to t the neck to the body.

The base of each guitar is the wood construction. The neck pocket in our kits is perfect.

There is no need to work the neck pocket other than maybe a simple sanding. Slide the

neck into the pocket and take the neckplate and the four big screws to fasten the neck.

Electronics

Take the pickups and thread the cables into the electronic cavity. Take two springs and two

long screws and slide the spring over the screw, screw the pickup into the body. Thread the

loose wire from the control plate harness and thread this into the hole that leads to the

opening under the bridge. This wire needs to make a connection to the bridge to prevent

hum. Now screw the bridge onto the body to secure the wire. Solder the pickup wires to

the potentiometers. See the attached diagram.

Check if both pickups and both the volume control and tone control work accordingly. If

everything works, you can close the electronic cavity.

Hardware

Install the machine head bushings. Lightly tap them into place with a hammer. Use some

wood or other material to prevent the bushings from getting damaged by the hammer.

Before drilling or punching a hole to secure the machine heads, please align the machine

heads on the back, so it looks neat and tidy. Now fasten all screws and nuts. A loose washer

or nut can cause unwanted resonance.

Put the strings on and start tuning your bass.

Now the bass needs a set up. Once tuned to pitch, check the neck curve and adjust to your

preference with the trussrod key. Check the frets for level. If the frets are not level enough

to your liking, level and polish the frets. Now adjust the string height so the guitar plays

comfortably all over the neck and there is no string buzz. The string height at the bridge is

set using the supplied small Allen wrench. The string height at the nut is set by ling the

string slots to the desired height. Intonation is set by adjusting the intonation screws.

Finish setting up with adjusting the intonation. Now you are ready. You have built your

JB-15 ! Have fun playing it!

Produkt Specifikationer

Mærke:	Boston Acoustics
Kategori:	Guitarforstærker
Model:	KIT-JB-15

Har du brug for hjælp?

Hvis du har brug for hjælp til Boston Acoustics KIT-JB-15 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Guitarforstærker Boston Acoustics Manualer

Boston Acoustics KIT-TE-45 Manual

5 Januar 2026

Boston Acoustics KIT-FV-15 Manual

3 Januar 2026

Boston Acoustics KIT-LP-45 Manual

2 Januar 2026

Boston Acoustics KIT-JB-15 Manual

2 Januar 2026

Boston Acoustics KIT-ST-35 Manual

2 Januar 2026

Boston Acoustics KIT-LP-15 Manual

2 Januar 2026

Guitarforstærker Manualer

Nyeste Guitarforstærker Manualer

Electro Harmonix Abrams 100 Manual

28 December 2025

Blackstar HT-1R MkII Manual

20 Oktober 2025

Blackstar Unity 250 Manual

19 Oktober 2025

Victory V4 The Kraken Manual

15 Oktober 2025

Electro Harmonix Crayon Manual

6 Oktober 2025

Electro Harmonix Battalion Manual

6 Oktober 2025

Electro Harmonix Signal Pad Manual

6 Oktober 2025

Electro Harmonix Analogizer Manual

6 Oktober 2025

Electro Harmonix Muff Overdrive Manual

6 Oktober 2025

Electro Harmonix Stereo Clone Theory Manual

5 Oktober 2025