Chamberlain 041DJ003MC Manual

Chamberlain Modtager 041DJ003MC

Læs gratis den danske manual til Chamberlain 041DJ003MC (24 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Chamberlain 041DJ003MC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/24
1
A
B
F
E
B
B
D
C
Logic Board
Model 041DJ003MC
Also replaces 050DCRJWF
WARNING: This product can expose you to chemicals
including lead, which are known to the State of California to
cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
To prevent possible SERIOUS INJURY or DEATH:
• Disconnect ALL electric and battery power BEFORE performing ANY
service or maintenance.
To prevent damage to the receiver/logic board, DO NOT touch printed
circuit board of replacement receiver/logic board during installation.
ALWAYS wear protective gloves and eye protection when changing the
battery or working around the battery compartment.
NOTICE: This device complies with Part 15 of the FCC rules and Industry
Canada’s license-exempt RSSs. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifi cations not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance
is maintained between users/bystanders and device.
This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules and Industry
Canada ICES standard. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Before you begin. Your new myQ® serial number is located on the
replacement label with your replacement logic board. You will need this new myQ
serial number to connect your opener to the network.
Disconnect power.1. 2. Open the front panel . (A)
Remove the battery cover. 3.
Disconnect the battery. Remove
the battery and set aside .(B)
Disconnect the wires coming 4.
from the safety reversing sensors,
door control, door lock and cable
tension monitor from the logic
board .(C)
Remove the logic board cover .5. (D)
Disconnect all the wiring harnesses 6.
from the logic board .(E)
Remove the four screws securing 7.
the logic board, remove the logic
board , and discard.(F)
Install the new logic board and 8.
connect the wiring harnesses. Route
the antenna through the channel in
the new battery cover.
Adhere the new myQ serial number 9.
label over the original label on the
logic board cover.
10. Set door profile for new replacement
logic board. See page 2 to set door
profile steps.
11. Reprogram the travel and test the
safety reversal system (see pages 2
and 3).
12. Program all remote controls and
keyless entries (see page 4).
13. Use the myQ app to add the new
myQ serial number to your account.
Red wire (+)
Battery Status LED
Black wire (-)
Antenna
NOTE: Be sure the short antenna is not pinched by the battery door and held in place
as shown.
NOTE: Please read these instructions as programming may be different from older
programming.

Produkt Specifikationer

Mærke: Chamberlain
Kategori: Modtager
Model: 041DJ003MC

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain 041DJ003MC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Chamberlain Manualer

Chamberlain

Chamberlain 041DJ003MC Manual

24 August 2024
Chamberlain

Chamberlain 050ACTBMC Manual

10 August 2024
Chamberlain

Chamberlain 050ACTBLKMC Manual

8 August 2024
Chamberlain

Chamberlain 050ACTWFLK Manual

6 August 2024
Chamberlain

Chamberlain 050ACTWFMC Manual

8 November 2022
Chamberlain

Chamberlain 050DCRJWFMC Manual

28 Oktober 2022

Modtager Manualer

Nyeste Modtager Manualer

Extron

Extron DTP3 R 201 D Manual

15 December 2025
Pure Acoustics

Pure Acoustics Maestra AVD5023 Manual

11 December 2025
Atoll

Atoll AM400 Evolution Manual

8 December 2025
Atoll

Atoll MA100 Manual

8 December 2025
Fostex

Fostex AP25 Manual

7 December 2025
Fostex

Fostex PC200USB-HR Manual

7 December 2025
Atoll

Atoll CD400 Evolution Manual

7 December 2025
Fostex

Fostex PC200USB Manual

7 December 2025
Fostex

Fostex AP05 Manual

6 December 2025
Atoll

Atoll AV500 Manual

6 December 2025