Chamberlain 050ACTBLKMC Manual

Chamberlain Modtager 050ACTBLKMC

Læs gratis den danske manual til Chamberlain 050ACTBLKMC (13 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Chamberlain 050ACTBLKMC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/13
1
DANGER PELIGRO•
132C2280- 3D
TO ERASE ALL
RECEIVER CODES
1. Pre ss and HO LD
re ce iver o range
ERASE but t o n
6 se co nds. Ind ica t o r
light will t urn O N.
2. Re le ase butt on
whe n light t urns O FF.
CANADA:
PART : DE PIEZA:NO. NO.
DATE:
T HE CHAMBER LAIN
GRO UP, INC ., US A
Ens am blad o e n Méxic o
Ass em bled in Mexi co
ELIMINACIÓN DE
TODOS LOS CÓDIG OS DEL
RECEP T OR
1. MANTENG A PRES IONADO
e l bo t ón nar an ja " ERASE "
de l rec ept or dura nt e 6
se gundo s. La luz de l
indica dor s e enc ende rá.
2. Sue lte el bo tó n cu ando la
luz se apa gue .
DANGER PELIGRO•
132C2280-3D
TO ERASE A LL
RECEIV ER CODE S
1.Pressand HOLD
receivero rang e
ERASE b u tto n
6 Ind icato rseco nd s.
lig h t wi ll turn ON.
2.Releasebu tto n
when lig h t tu rns OF F.
CANADA:
P : ARTN O. N O.DEPIEZA:
DATE:
THE C H A M BER LAI N
GROU P, I N C ., U SA
EnsambladoenMéxico
Assembled Mexico i n
ELIM INAC IÓN DE
TODOSLO S CÓD IGOS D EL RECEP TOR
1. P RES IONADO MANTENGA
el b o tó n naranja "ERASE "
d el receptor 6 d u rante
segund o s. La lu z d el ind i cado r seencend erá.
2. el cuand o Suelte b o tó n la
luz seapague.
Before you begin
1
Installation
RECEIVER LOGIC BOARD REPLACEMENT
Models 050ACTBMC and 050ACTBLKMC
Replaces 050ACTWF and 050ACTWFLK
1.2 To maintain your warranty, place the
provided label over the existing label
on the end panel of the garage door
opener.
1.1 Remove the light lens by pulling the
top sides of the light lens and rotate the
light lens down. Squeeze the light lens
clips to remove lens from end panel.
Your garage door opener has an internal gateway located on the receiver logic board. After installing the new receiver logic board, use the myQ
® serial number found on the provided label to add your
garage door opener to your myQ account. The products illustrated in the instructions are for reference. Your product may look different.
1.3 Disconnect power to the garage door
opener.
Remove the receiver logic board
2
2.1 Disconnect the wires from the quick-connect terminals ( ). A
Remove the receiver logic board end panel from the garage
door opener.
2.2 Unplug the wire harnesses from the receiver logic
board. You may need needle-nosed pliers to remove
the harnesses.
To prevent possible SERIOUS INJURY or
DEATH:
• Disconnect ALL electric and battery
power BEFORE performing ANY service
or maintenance.
To prevent damage to the receiver/logic
board, DO NOT touch printed circuit board
of replacement receiver/logic board during
installation.
ALWAYS wear protective gloves and eye
protection when changing the battery or
working around the battery compartment.
A
To insert or remove
the wires from the
terminal, push in the
tab with a
screwdriver tip.
Red
White
White
Grey
2.3 Remove the receiver
logic board from the
end panel by removing
the 2 screws and
releasing the 2 clips.
Screws
Wire clip
Clips
WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth
defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
2
Install new receiver logic board
3
3.3 Reinsert the wires.
Door control wires:
• white wire into the white terminal.
• white/red wire into the red terminal.
Safety sensor wires:
• white wires into the white terminal.
• white/black wires into the
grey terminal.
NOTE: A test of the safety reverse system is necessary for safe operation.
To insert or remove the
wires from the terminal,
push in the tab with a
screwdriver tip.
1
Programming
1.1 Press and release the Learn button on the garage door opener. The Learn indicator light
will glow steadily for 30 seconds.
1.2 Within 30 seconds, press and hold the
button on the remote control.
1.3 Release the button when the garage
door opener light blinks. It has learned
the code. If light bulbs are not installed,
two clicks will be heard.
Program a remote control using the learn button
Learn
Indicator
Light
Yellow Learn
Button
3.4 Install the light lens by aligning with
the hinges and snapping into place.
Reconnect power.
NOTE: When installing the light lens, ensure the antenna
wires are hanging straight down.
Red
White
White
Grey
To program the Wi-Fi garage door opener to your network refer to your owner’s manual.
3.2 Insert the antenna wires through
the holes in the end panel. Snap the
receiver logic board into place on the
end panel and fasten with screws.
NOTE: Some models
will require the short
antenna wire to be
placed in the traps of
the end panel.
Antenna wires
Antenna
wires
3.1 Connect the wire harnesses to the
new receiver logic board. When
reconnecting the wire harness, be sure
the tabs on the wire harness are facing
the end panel, not the logic board.
Logic Board
Wire Clip
End Panel
Wire
Harness
Tabs
NOTE: If you have model
8365W-267 or 8365WRGD-267,
remove the plastic post off the
end panel for the logic board
to seat properly or order a
replacement part end panel, part
number 041D0210-1.
Reconnect the end panel to the garage
door opener.

Produkt Specifikationer

Mærke: Chamberlain
Kategori: Modtager
Model: 050ACTBLKMC

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain 050ACTBLKMC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Chamberlain Manualer

Chamberlain

Chamberlain 041DJ003MC Manual

24 August 2024
Chamberlain

Chamberlain 050ACTBMC Manual

10 August 2024
Chamberlain

Chamberlain 050ACTBLKMC Manual

8 August 2024
Chamberlain

Chamberlain 050ACTWFLK Manual

6 August 2024
Chamberlain

Chamberlain 050ACTWFMC Manual

8 November 2022
Chamberlain

Chamberlain 050DCRJWFMC Manual

28 Oktober 2022

Modtager Manualer

Nyeste Modtager Manualer

Planet Audio

Planet Audio PSX26 Manual

15 Juni 2025
Planet Audio

Planet Audio AC1200.2 Manual

15 Juni 2025
Planet Audio

Planet Audio AC2400.4 Manual

15 Juni 2025
Planet Audio

Planet Audio AC2600.2 Manual

15 Juni 2025
Planet Audio

Planet Audio PL1500.1M Manual

15 Juni 2025
Ecler

Ecler HSA2-400ES Manual

15 Juni 2025
Planet Audio

Planet Audio PL4000.1D Manual

15 Juni 2025
Planet Audio

Planet Audio MB1200.4D Manual

15 Juni 2025
Pure Acoustics

Pure Acoustics AZ-2U-3240 Manual

15 Juni 2025
Ecler

Ecler AURA-4B600 Manual

15 Juni 2025