Chapin 1949 Manual

Chapin Ikke kategoriseret 1949

Læs gratis den danske manual til Chapin 1949 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Chapin 1949, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

6-6092

Hose Black

Manguera para trabajos pesados Negro

Tuyau pour service intense Noir

6-6091

Hose Brown

Manguera Castaño

Tuyau Brun (1949)

6-6062

Shut-off Handle

Mango de cierre

Poignée du robinet

6-5943

Nozzle 1.0 GPM

Tobera

Buse

6-7703

Extension wand, Vara de extensión, Rallonge (1949)

6-7734

Extension wand, Vara de extensión, Rallonge (1979)

017649 (A) R0421

6-5797

Nozzle .5GPM

Tobera

Buse

6-7745

Filtered outlet tube

Tubo de salida con ﬁltro, Tube de sortie avec ﬁltre (19

6-5373

Holster

Funda

Étui

6-4629

Repair Parts Kit Gaskets and Seals (not included)

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus)

1949

Sk-1154-1

WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious

eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave

a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.

Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants

and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.

Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump

assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than

the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original

parts. Never spray ﬂammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,

pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instructions

before use with this sprayer as some chemicals may be hazardous when used with this sprayer.

WARNING

Note: Your particular sprayer may not include all parts pictured above.

Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Parts, Piezas, Pièces

Congratulations!

You have just purchased a quality Chapin product.

Call us @ 1-800-950-4458 or www.chapinmfg.com

1. Hose to Tank

2. Nozzle

Attach the hose by screwing the swivel

nut clockwise and tightening to 37 in. lbs.

Refer to Pre-use check before using.

Attach nozzle to shut-off handle or extension wand.

TO LOCK HANDLE: Push handle down to

depress coil spring and turn handle 1/4

turn clockwise, then allow handle to raise

into lock position.

5. Pressurizing and Spraying

Lock

Position

2A 2B

3. Pre-Use Check

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are

found, replace hose before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and

exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates

possible tank weakening and could result in explosive bursting under pressure. If any of these

signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as

this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only

(Pump plunger 10-20 strokes and inspect for leaks).

5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.

6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank,

and proceed with Filling, Pressurizing and Spraying Instructions.

7) Do: Inspect all metal parts including the wand, nozzle and ﬁttings for rust, corrosion and pitting.

If any of these conditions are found, replace affected part with original manufacturer’s part

before using.

4. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over ﬁll to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and

tighten securely.

TO RELEASE HANDLE:

Push down to depress

coil spring and turn

handle counterclockwise

1/4 turn, then lift handle.

Pump until you feel

resistance.

TO LOCK PUMP: Place pump prongs

down into slots in funnel, turn clamp

clockwise to furthest position under

bottom slot, then turn handle clockwise

until tightly locked and sealed in place.

TO UNLOCK PUMP: Turn

handle counterclockwise

until 3-prong clamp is

loose. Then rotate clamp

counterclockwise to stop

and lift out.

5C5C

5D5D

5. Pressurizing and Spraying, continued

5E5E

5F5F

6. Fatigue-Free Spraying

For constant spraying, push down on shut-off handle

and move locking mechanism away from you. To

release, squeeze handle and move the locking

mechanism back towards you.

7. To Release Pressure

1) With pump facing away, turn locked handle counterclockwise until air begins to escape. Do:

Stop turning handle when you hear air escaping.

2) Do: Stay away from the sprayer until all air has escaped.

8. Care, Storage and Maintenance

1) Do: Follow chemical manufacture’s instructions for cleaning. Rinse thoroughly with

recommended solvent. Follow Filling, Pressurizing and Spraying Instructions, except pump unit

only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed after each use.

2) Do: Open shut-off and allow recommended solvent to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening

in cover.

6A6A

P.O. Box 549 700 Ellicott St.

Batavia, NY 14021-0549 U.S.A.

1-800-950-4458 www.chapinmfg.com

FOR HELP USING TRI-LOCK PUMP SEE VIDEO

https://chapinmfg.com/pages/industrial-videos

Produkt Specifikationer

Mærke:	Chapin
Kategori:	Ikke kategoriseret
Model:	1949
Vægt:	4950 g
Produktfarve:	Rød
Volumen:	13200 ml
Driftstryk:	4 bar

Har du brug for hjælp?

Hvis du har brug for hjælp til Chapin 1949 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Chapin Manualer

17 September 2025

27 August 2025

27 August 2025

26 August 2025

26 August 2025

22 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Witt Smart Touch Air Pump Manual

3 November 2025

ANCEL HD3400 Manual

3 November 2025

Fromm & Starck STAR_MCAB_16 Manual

3 November 2025

Slingshot R (2022) Manual

3 November 2025

Beverage-Air WTFCS52HC-60 Manual

3 November 2025

ANCEL V6 PRO Manual

3 November 2025

Leviton 5304M-2N7 Manual

3 November 2025

ANCEL BST500 Manual

3 November 2025

Beverage-Air Horizon HRP1HC-1S Manual

3 November 2025

FreeMotion P50 Manual

3 November 2025