Chord Blu Manual

Chord Ikke kategoriseret Blu

Læs gratis den danske manual til Chord Blu (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 147 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 74 anmeldelser. Har du et spørgsmål om Chord Blu, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Connecting BLU MKII to DAVE 3.0

Connect BLU MKII to DAVE via dual data mode. You can use either

BNC 1 and 2 or BNC 3 and 4. Navigate forward (not backwards) to

BNC 1 if outputs from BLU MKII are connected to BNC inputs 1 and 2

on DAVE, or navigate to BNC 3 if outputs from BLU MKII are connected

to BNC inputs 3 and 4.

Chord Electronics

BLU MKII | Quickstart Manual

The Pumphouse, Farleigh Lane, East Farleigh, Kent, ME16 9NB, United Kingdom

info@chordelectronics.co.uk

chordelectronics.co.uk

Quickstart Manual

Introduction 1.0

Welcome to the Blu MK II Quickstart Guide. This shortened guide is

supplementary to the main manual which should be referred to for full

safety and operational information.

Please note, more information on any of these topics is listed within the

full manual found under the product page:

chordelectronics.co.uk/product/blu-mk-2

Warranty 1.1

The BLU MK II comes with a comprehensive 5-year warranty. To

activate this warranty, please register your device via the Chord

Electronics website:

chordelectronics.co.uk/register-product

Connecting to a source 2.0BLU MKII

In order to use your BLU MKII as an upscaler/upsampler, you must

connect your source to any input of BLU MK II. You can connect up to

2 devices. When using a MAC/Linux device with USB you will not need

a driver but a Windows device will need a driver from the BLU MKII

section of our website:

chordelectronics.co.uk/product/blu-mk-2

USB

Input

BNC

Input

Connecting BLU MKII to third-party DACs 4.0

Use the Dual BNC, single BNC or AES outputs to connect your BLU

MKII with a third-party DAC. Dual BNC will only fuction with the 2

further right hand side BNC ports. The bottom left BNC port can not

be used as a Dual BNC connector.

For single BNC connectors use any of the 3 BNC outputs shown below

in Blue. The top left hand side BNC port is only to be used for an input

into the BLU MKII.

Output

Chord Electronics

BLU MKII | Quickstart Manual

The Pumphouse, Farleigh Lane, East Farleigh, Kent, ME16 9NB, United Kingdom

info@chordelectronics.co.uk

chordelectronics.co.uk

Quickstart Manual

Connecting BLU MKII to power 6.0

Connect the supplied IEC cable to the input of BLU MKII. Please make

sure none of your other devices are switched on at this point.

Opening the CD mechanism 8.0

Now that you have successfully completed the setup of your BLU MKII

you can immediately begin to experience its transformational quality

on your digital music collection. However, we advise that you register

your product with us. Registering helps us give you the best possible

support and protects your investment:

Product registration 10.0

chordelectronics.co.uk/register-product/

Display and basic operation 9.0

Powering up BLU MKII 7.0

With all devices correctly connected, the system is ready for playback.

Again, ensure any volume controls are set to the minimum before

switching on your source and pre-ampliﬁer, then power ampliﬁer. This

sequence should always be followed to protect connected devices.

Commence playback before slowly increasing the volume to a

comfortable listening level.

With BLU MKII you are able to choose which upsample rate is best

ﬁtted for your system. On the back of BLU MKII are 2 switches, one is

the sample rate switch and the other the dither switch. In this section

we will talk about the sample rate switch on the left hand side of BLU

MKII. See the table below for switch positions.

For use with the DAVE we recommend using high upsampling to get

the best out of your experience. For third-party DACs, refer to their

manual to select the best rate suited.

Setting the upsampling qualities 5.0

POSITION - UP: Upsampling Low

(for more information view full manual)

POSITION - MID: Upsampling Medium

(for more information view full manual)

POSITION DOWN: Upsampling High

(for more information view full manual)

To open the CD lid, locate the hinge at

the rear and gently lever the sprung

mechanism in a ﬂuid downward

motion (never apply force). Gently

use the hinge to lever the lid open or

closed.

1 3 4

PROGRAM SCAN SHUFFLE

TRACK

A - B

TOTAL

REPEAT 1

REM TIME

PAUSE

1 2

3 4

Track no.

Seconds

Play status

Dual data indicator

Minutes

All basic CD functions can be accessed through the top pannel

buttons. Below is a diagram of the screen section system, using the

top panel buttons to navigate.

Produkt Specifikationer

Mærke:	Chord
Kategori:	Ikke kategoriseret
Model:	Blu

Har du brug for hjælp?

Hvis du har brug for hjælp til Chord Blu stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Chord Manualer

12 August 2025

11 August 2025

19 Marts 2025

3 Marts 2025

3 Marts 2025

4 September 2024

8 August 2024

30 Juli 2024

8 Marts 2024

30 Juni 2023

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

T'nB FMCT03BT Manual

16 September 2025

T'nB MWERGOVLEFT Manual

16 September 2025

T'nB AD300 Manual

16 September 2025

T'nB CARBTKIT3 Manual

16 September 2025

T'nB MHMECADUAL Manual

16 September 2025

T'nB VINEKIT Manual

16 September 2025

T'nB PADA36W Manual

16 September 2025

T'nB TCUNSAM Manual

16 September 2025

Ikea HATTHOLMEN 105.084.80 Manual

16 September 2025

T'nB MHFIXDUAL Manual

15 September 2025